beautypg.com

Dc a, Operation, Page 3 – Whelen IX43UFX User Manual

Page 3

background image

Page 3

PART NUMBER KEY

0 1 - 0 6 8 7 4 1 7 - _ _

YEAR/MAKE

2013 FUSION

C =

VERSION

10 LT W/TD

12 LT WO/TD

3 =
4 =

2

1 4 - 0 4 0 2 8 6 - 0 6 D SCREW, 4-40 X 3/8 PAN TORX HD ROLOK SS

8

1 4 - 0 8 2 2 8 C - 0 6 D SCREW, 8-32 X 3/8" PAN TORX HD ROLOK SS BLK OXIDE

1

3 9 - 1 M 1 7 6 7 2 - 0 8 HOUSING, PLUG 8 POS 18 AWG SL-156 W/ LOCKING RAMP

1

4 6 - 0 7 4 3 4 0 3 - 0 0 ASS'Y, CABLE 9/C 18 GA TPR 20' SL-156 SCKTS ONE END

1

2 6 - 0 2 1 5 0 0 1 - 0 6 TY WRAP, 6" BLACK

1

0 1 - 0 2 6 E 4 9 2 - 0 0 SUB ASSY, LC I/O INNER-EDGE XLP

1

4 6 - 0 7 6 E 4 9 5 - 0 0 ASSY, HARNESS PASSENGER INNER EDGE XLP

1

4 6 - 0 7 6 E 4 9 5 - 0 1 ASSY, HARNESS DRIVER INNER EDGE XLP

0 1 - 0 2 6 E 4 8 8 - 3 1 SUB ASSY, TAKE DOWN WHITE INNER-EDGE XLP

A/R

0 1 - 0 2 6 E 4 8 8 - 1 0 SUB ASSY, WARNING AMB INNER-EDGE XLP

A/R

0 1 - 0 2 6 E 4 8 8 - 2 0 SUB ASSY, WARNING BLU INNER-EDGE XLP

A/R

0 1 - 0 2 6 E 4 8 8 - 3 0 SUB ASSY, WARNING WHT INNER-EDGE XLP

A/R

0 1 - 0 2 6 E 4 8 8 - 4 0 SUB ASSY, WARNING GRN INNER-EDGE XLP

A/R

0 1 - 0 2 6 E 4 8 8 - 5 0 SUB ASSY, WARNING RED INNER-EDGE XLP

2

3 8 - 0 5 4 6 8 2 7 - 1 4 TRIM, SEAL HSNG/WINDSHIELD 13.600" LGTH INNER EDGE XLP

1

1 0 - 0 5 6 E 5 6 3 - 3 0 LABEL, WHELEN LOGO, 2.75" GREY

0 1 - 0 6 8 7 4 1 7 - _ 3 INNER EDGE XLP, LOW CURRENT 10 LT W/TD
0 1 - 0 6 8 7 4 1 7 - _ 4 INNER EDGE XLP, LOW CURRENT 12 LT WO/TD

2
8

1
1
1
1
1
1

2

A/R
A/R
A/R
A/R
A/R

2

1

LABEL, INNER EDGE XLP, M/N P/N

1 0 - 0 5 6 E 5 0 1 - _ _

1

1

SCREW, 4-40 X 1/4 PPHMS 410SS BLACK PASSIVATE

1 4 - 0 4 0 2 1 6 - 0 4 H

24 24

2

3

ITEM

PART NUMBER

DESCRIPTION

QTY QTY

11

12

13

14

15

16

17

18

4

5

6

7

8

9

10

1

B

15

14

18

16 17

13

2

2

10

1

7

3

D

C

A

0 1 - 0 6 8 7 4 1 7 - C _ FINAL, INNER EDGE XLP, 10/12 LIGHT

E

A

C

B

D

F

11 - 2 6 E 8 9 0 - 1 0 7
11 - 2 6 E 8 9 0 - 0 0 7
0 7 - 2 8 7 5 2 9 - 1 2 3
0 7 - 2 8 7 5 2 9 - 0 2 3

11 - 3 6 E 8 9 1 - 0 0 7

11 - 3 6 E 8 9 1 - 1 0 7

BASE, HOUSING DRVR 2013 FUSION INNER EDGE XLP BLACK

COVER, TOP DRVR FORD FUSION DUO INNER EDGE XLP BLK
COVER, TOP PASS FORD FUSION DUO INNER EDGE XLP BLK

BASE, HOUSING PASS 2013 FUSION INNER EDGE XLP BLACK

BRACKET, VISOR MT DRVR FUSION INNER EDGE XLP BLACK
BRACKET, VISOR MT PASS FUSION INNER EDGE XLP BLACK

1

1

1
1

1

1

2 1 - 1 2 0 8 1 2 0 5 - 3

SCREW GROMMET, FASTEX # 212-240602-040101

G

2
2

H

1 5 - 1 3 1 4 1 6 - 2 0 2

SCREW, 1/4 X 1 1/4 PPHSMS SS TYPE A

2

I

1 5 - 0 8 1 4 1 6 - 1 6 0

SCREW, 8 X 1 PPHSMS

ITEM

PART NUMBER

DESCRIPTION

QTY

NOT

SHOWN

Operation:

This lightbar is powered and controlled by an 8-conductor cable exiting
the lightbar. All functions listed here are not present in all lightbars.

White/Green - Scan-Lock™

The WHITE/GREEN wire allows you to choose from the available flash
patterns. First you must activate the lighthead(s) you wish to change:

TO CYCLE THROUGH ALL PATTERNS: To cycle forward apply +12 VDC to
the WHT/GRN wire for less than 1 second and release. to cycle backward
apply +12 VDC to the WHT/GRN wire for more than 1 second and release.
TO SET A PATTERN AS DEFAULT: When the pattern is displayed, allow it to
run for over 5 seconds. The lighthead will now display this pattern when active.

TO RESET TO THE FACTORY DEFAULT PATTERN: Turn off power and
apply +12 VDC to the WHT/GRN wire while turning power on.
A normally open momentary switch is best used for Scan-Lock operation.

Blue: Flash 1

Apply +12 VDC to the BLU wire to activate the warning lights. Fuse this wire @
1 Amp.

Brown: Hi/Low Power

The low power feature allows you to step the lightbar down to run in low power
for night time use. Fuse this wire @ 1 Amp. An SPST switch can be used to
control Hi/Low power. To activate Low power operation: Apply +12 VDC to
the BRN wire. To restore regular power: Remove voltage from the BRN wire.

White/Black: Take-Downs

Apply +12 VDC to the WHT/BLK wire to activate the take-downs. Fuse this wire
@ 1 Amp. NOTE: Not used with 12 Light models.

White/Orange: Flashing Take-Down

Apply +12VDC to the WHT/ORG wire to activate flashing take-down mode.
Fuse this wire @ 1 Amp. Note: The WHT/BLK wire overrides this display.
NOTE: Not used with 12 Light models.

Orange: California Steady

Apply +12 VDC to the ORG wire to activate lightheads using the California
Steady pattern table. Refer to the artwork on the following page for lighthead
identification. Fuse this wire @ 1 Amp.

Available Flash Patterns:
1.

ActionScan™

2.

SignalAlert™ 75 ...... Alternating

3.

SignalAlert™ 75 .................Multi

4.

CometFlash® 75...... Alternating

5.

CometFlash® 75.................Multi

6.

DoubleFlash 75 ....... Alternating

7.

DoubleFlash 75 ..................Multi

8.

SingleFlash 75......... Alternating

9.

SingleFlash 75....................Multi

10. LongBurst 75........... Alternating
11. LongBurst 75......................Multi
12. SingleFlash 60......... Alternating
13. SingleFlash 60....................Multi
14. SingleFlash 90......... Alternating
15. SingleFlash 90....................Multi
16. SingleFlash 120....... Alternating
17. SingleFlash 120..................Multi
18. SingleFlash 240....... Alternating
19. SingleFlash 240..................Multi
20. DoubleFlash 120 ..... Alternating

21. DoubleFlash 120 ...............Multi
22. ActionFlash™ 75 ... Alternating
23. ActionFlash™ 75 ..............Multi
24. ActionFlash™ 150 . Alternating
25. ActionFlash™ 150 ............Multi
26. MicroBurst™ .......... Alternating
27. MicroBurst™ .....................Multi
28. PingPong................ Alternating
29. PingPong...........................Multi
30. FlimFlam................. Alternating
31. FlimFlam............................Multi
32. ModuFlash.............. Alternating
33. ModuFlash.........................Multi
34. Cylon 1
35. Cylon 2
36. Cylon Chaser
37. Eyeballs Sync
38. Eyeballs In/Out
39. 2 Eyeballs In/Out
40. Eyeballs Crazy

California Steady Pattern Table:
#

Active Lightheads

1.

D1

2.

D2

3.

D3

4.

D4

5.

D5

6.

D6 (12-Light Models Only)

7.

D1 + P1

8.

D2 + P2

9.

D3 + P3

10.

D4 + P4

11.

D5 + P5

12.

D6 + P6 (12-Light Models Only)

IMPORTANT! Before returning this vehicle to active service, visually
confirm the operation of this product, as well as all vehicle
components/equipment.
WARNING! All customer supplied wires that connect to the positive
terminal of the battery must be sized to supply at least 125% of the
maximum operating current and FUSED at the battery to carry that
load. DO NOT USE CIRCUIT BREAKERS WITH THIS PRODUCT!