Whelen IX37UFZ - Manual (Page 2)

Page 2
10 X 1" PHILLIPS PAN
HD SHEET METAL SCREW
(type A) (QTY 1)
#8-32 x 3/8 TORX HD SCREW (QTY 2)
VISOR SWIVEL
BRACKET
Passenger Side Shown
VISOR
CLIP
MOUNTING
BRACKET
SHEET
METAL
ROOF
RUBBER SEAL
Lightbar
Side View
WI
ND
SH
IEL
D
VISOR CLIP BRACKET
Fig. 1
SHEET METAL
Slip over visor
clip bracket
Slide under visor
swivel bracket
Side View
HEADLINER
IMPORTANT! Before mounting this unit refer to the AIR BAG
WARNING on page 1. Read all warnings before beginning.
IMPORTANT! The lightbar should be located a minimum of 16" from
any radio antennas!
Installation:
Note: When routing wires, it is important to choose a path that will keep
the wires away from excessive heat or any vehicle equipment that could
compromise the integrity of the wires (ex. trunk lids, door jams, etc.)
1. Secure the mounting bracket to the Inner Edge housing using the two
#8 - 32 X 3/8 TORX HEAD SCREWS provided (Fig. 1).
2. Loosen (do not remove) the screws securing the passenger-side visor swivel
bracket to the vehicle.
3. Slide the outside end of the mounting bracket under the visor swivel bracket
(Fig. 1). At the same time slip the rectangular hole in the other end of the
mounting bracket over the visor clip bracket (Fig. 1). With the mounting
bracket in position retighten the visor swivel bracket hardware.
4. Using the screw hole in the mounting bracket as a guide, carefully drill a pilot
hole (for a #10 sheet metal screw) into the sheet metal
behind the headliner and secure the other side of the
mounting bracket using the supplied #10 X 1”
PHILLIPS PAN HEAD SHEET
METAL SCREW.
5. Repeat this procedure for the driver-side assembly.
6. When properly mounted, the rubber seal will be in full contact with the
vehicle windshield and roof. This is to prevent light output from entering the
passenger compartment. When this has been achieved, tighten all mounting
hardware firmly to maintain contact (Fig. 1).
7. Route the lightbar cable down the vehicle A-pillar to your control head.
8. Make all wiring connections using the information in the wiring diagram.
Wiring:
WARNING! All customer supplied wires that connect to the positive
terminal of the battery must be sized to supply at least 125% of the
maximum operating current and FUSED at the battery to carry that load.
DO NOT USE CIRCUIT BREAKERS WITH THIS PRODUCT!
Operation:
This lightbar is powered and controlled by an 8-conductor cable exiting
the lightbar. All functions listed here are not present in all lightbars.
White/Green - Scan-Lock™
The WHITE/GREEN wire allows you to choose from the available flash
patterns. First you must activate the lighthead(s) you wish to change:
TO CYCLE THROUGH ALL PATTERNS: To cycle forward apply +12 VDC to
the WHT/GRN wire for less than 1 second and release. to cycle backward
apply +12 VDC to the WHT/GRN wire for more than 1 second and release.
TO SET A PATTERN AS DEFAULT: When the pattern is displayed, allow it to
run for over 5 seconds. The lighthead will now display this pattern when active.
TO RESET TO THE FACTORY DEFAULT PATTERN: Turn off power and
apply +12 VDC to the WHT/GRN wire while turning power on.
A normally open momentary switch is best used for Scan-Lock operation.
Blue: Flash 1
Apply +12 VDC to the BLU wire to activate the warning lights. Fuse this wire @
1 Amp.
Brown: Hi/Low Power
The low power feature allows you to step the lightbar down to run in low power
for night time use. Fuse this wire @ 1 Amp. An SPST switch can be used to
control Hi/Low power. To activate Low power operation: Apply +12 VDC to
the BRN wire. To restore regular power: Remove voltage from the BRN wire.
White/Black: Take-Downs
Apply +12 VDC to the WHT/BLK wire to activate the take-downs. Fuse this wire
@ 1 Amp. NOTE: Not used with 12 Light models.
White/Orange: Flashing Take-Down
Apply +12VDC to the WHT/ORG wire to activate flashing take-down mode.
Fuse this wire @ 1 Amp. Note: The WHT/BLK wire overrides this display.
NOTE: Not used with 12 Light models.
Orange: California Steady
Apply +12 VDC to the ORG wire to activate lightheads using the California
Steady pattern table. Refer to the artwork on the following page for lighthead
identification. Fuse this wire @ 1 Amp.
IMPORTANT! Before returning this vehicle to active service, visually
confirm the proper operation of this product, as well as all vehicle
components/equipment.
California Steady Pattern Table:
#
Active Lightheads
1. D1
2. D2
3. D3
4. D4
5. D5
6. D6 (12-Light Models Only)
7. D1 + P1
8. D2 + P2
9. D3 + P3
10. D4 + P4
11. D5 + P5
12. D6 + P6 (12-Light Models Only)
CAUTION! DO NOT LOOK DIRECTLY AT THESE LED’S WHILE THEY ARE ON.
MOMENTARY BLINDNESS AND/OR EYE DAMAGE COULD RESULT!
I M P O R TA N T W A R N I N G !
Available Flash Patterns:
1.
ActionScan™
2. SignalAlert™ 75 ......Alternating
3. SignalAlert™ 75 ................ Multi
4. CometFlash® 75......Alternating
5. CometFlash® 75................ Multi
6. DoubleFlash 75 .......Alternating
7. DoubleFlash 75 ................. Multi
8. SingleFlash 75.........Alternating
9. SingleFlash 75................... Multi
10. LongBurst 75...........Alternating
11. LongBurst 75..................... Multi
12. SingleFlash 60.........Alternating
13. SingleFlash 60................... Multi
14. SingleFlash 90.........Alternating
15. SingleFlash 90................... Multi
16. SingleFlash 120.......Alternating
17. SingleFlash 120................. Multi
18. SingleFlash 240.......Alternating
19. SingleFlash 240................. Multi
20. DoubleFlash 120 .....Alternating
21. DoubleFlash 120 .............. Multi
22. ActionFlash™ 75....Alternating
23. ActionFlash™ 75.............. Multi
24. ActionFlash™ 150..Alternating
25. ActionFlash™ 150............ Multi
26. MicroBurst™ ..........Alternating
27. MicroBurst™ .................... Multi
28. PingPong ................Alternating
29. PingPong .......................... Multi
30. FlimFlam .................Alternating
31. FlimFlam ........................... Multi
32. ModuFlash..............Alternating
33. ModuFlash........................ Multi
34. Cylon 1
35. Cylon 2
36. Cylon Chaser
37. Eyeballs Sync
38. Eyeballs In/Out
39. 2 Eyeballs In/Out
40. Eyeballs Crazy
To
+12VDC
(fuse ea. @ 1A
WHT/GRN
BROWN
BLUE
ORANGE
WHT/BLK
*
WHT/ORG *
BLK
RED
Scan-Lock
Low Power
Flash 1
CA Steady
Take-Downs
Flashing T-D
Ground (-)
+12VDC
Fuses & Switches Customer Supplied
* Not used with 12 light models
5 Amp Fuse
Momentary Switch
SPST Switch
SPST Switch
SPST Switch
SPST Switch
SPST Switch
BATTERY
Wire Color Function