Whelen JE2NFPA - Manual (Page 2)

Page 2
Mounting
Pad
1/4 INTERNAL
TOOTH LOCK
WASHER
1/4 - 20 X 1-1/2
PHILLIPS PAN
HEAD METAL
SCREW
1/4 - 20 X 7/16 HEX NUT
Locking
Plate
1/4-20 X 1/2
SET SCREW
Fig. 1
Insert foot into extrusion
with locking plate
attached. Twist foot into
position
ANCHOR
PLATE
loosely secure foot and anchor plate.
slide foot
under lip
Fig. 2 Fig. 3 Fig. 4
IMPORTANT! The lightbar should be a minimum of 16” from any radio antennas!
Permanent Mounting:
1. Locate the mounting foot and locking plate included with your lightbar. If not already present,
install the locking plate onto the mounting foot using the supplied allen set screws (Fig. 1).
2. Flip the lightbar upside-down to expose the bottom of the extrusion and slide the anchor
plate onto the extrusion (Fig. 2).
3. Place the mounting foot into the extrusion and rotate the foot so that the top of the foot
swings into position under the lips in the extrusion (Fig. 3).
4. Repeat this procedure for the remaining mounting foot and return the lightbar to its right
side-up position.
5. Position the lightbar onto the vehicle roof in the desired mounting location. One often selected
location is directly above the B-pillars. This area is the strongest part of the roof. Check the light
bar cable exit location to be sure that the lightbar is facing the proper direction.
6. Adjust the two mounting feet outwards so that they are as close to the edge of the roof as possible.
Make sure that both mounting feet are in full contact with the roof. Be sure that there is no less than 1/2”
clearance between the roof and the lightbar at their closest point. When the mounting feet are in their proper
position, lightly tighten the mounting foot allen head set screws.
7. Turn the lightbar upside down and firmly tighten all of the set screws then slide the anchor plate up to the
mounting foot and tighten the anchor plate set screws (Fig.4).
8. Place the lightbar in its final mounting position on the vehicle, mark the mounting hole locations off onto the mounting surface, remove the lightbar
and drill the mounting holes.
9. Place the lightbar back onto the vehicle lined up with the mounting holes and secure the mounting feet to the vehicle using the supplied hardware.
Caution: Permanent mounting of this product will require drilling. It is absolutely necessary to make sure that no other vehicle components
could be damaged by this process. Check both sides of the mounting surface before starting. If damage is likely, select a different mounting
location.
NOTE: Unless otherwise specified, the lightbar mounting feet must be sitting as close to the edge of the roof as possible and in full contact
with the roof and not be hanging off the edge.
IMPORTANT: For strap mounting, be sure you have the right sized lightbar for your
vehicle. The bar should be approximately the same width as the vehicle roof. If too
large or small it will not mount properly and may come loose during driving.
1/2" MIN. CLEARANCE
FRONT
Driver-side
cable exit
Passngr.-side
cable exit
C a b l e A c c e s s H o l e L i g h t b a r d i s t a n c e f r o m v e h i c l e
Drill the cable access hole in the
appropriate area for your lightbar.
Lightbar Operation:
The standard lightbar uses a 2 and 4 wire
cable.
WARNING! All Customer supplied wires
that connect to the positive terminal of
the battery must be sized to supply at
least 125% of the maximum operating
current and FUSED at the battery to carry
that load. DO NOT USE CIRCUIT
BREAKERS WITH THIS PRODUCT!
RED FRONT LEDS (+)12V
RED/WHT REAR LEDS
BLACK FRONT LEDS
BLACK/WHT REAR LEDS
(+)12V
(-) GROUND
(-) GROUND
Justice™ Competitor Series NFPA Lightbar
CLEAR LED's
(+)12V:
GROUND: CLEAR LED's
RED Clear LED's
BLACK
RED LED's
BATTERY
NOTE:
All fuses and switches
are customer supplied.
SPST SWITCHES FUSES
3 AMP
3 AMP
7.5
AMP
CAUTION! DO NOT LOOK DIRECTLY AT THESE LED’S
WHILE THEY ARE ON. MOMENTARY BLINDNESS AND/OR
EYE DAMAGE COULD RESULT!
IMPORTANT WARNING!