Whelen SAK24 - Manual (Page 2)

Page 2
SA315 / Rear View
wire
exit &
drain
hole
A
A
A A
1/4" INTERNAL
TOOTH LOCK
WASHER
IMPORTANT: For drainage purposes, the speaker must be oriented so the wire
passage/drain hole is in the “6 o’clock” position (closest to the road). Improper
mounting will result in premature driver failure and void the product warranty.
IMPORTANT: The SA315 mounting kit comes with 3 long bolts (1/4-20 X 1-1/2” Hex Head). The longer
bolts are necessary to go through the mounting bracket, siren housing and into the siren driver. They
will replace 3 of the 4 shorter bolts (“A”) now secure the driver to the speaker housing.
short bolt be used in the
hole that go through the bracket so it will properly secure the driver to the housing.
If you need to move the location of any of the short bolts try not to remove all of them at
once . If you do
need to remove all 4 bolts at once be sure to hold the driver securely in place.
must
does not
since there will be nothing to hold the siren driver to the speaker housing
which Your
speaker is shipped with 1 or more of the short bolts installed. A
Mounting the speaker to the bracket:
1/4 - 20 X 1-1/2"
HEX HEAD SS
(Speaker & Bracket)
1/4 - 20 X 1-1/2"
HEX HEAD SS
(Speaker & Bracket)
1/4" INTERNAL
TOOTH LOCK WASHER
1/4
(Speaker & Bracket)
- 20 X 1-1/2"
HEX HEAD SS
1/4 X 20 X 1-1/4 HEX HEAD
(Speaker Only)
1/4 X 20 X 1-1/4 HEX HEAD
(Speaker Only)
1/4 X 20 X 1-1/4 HEX HEAD
(Speaker Only)
SA315 / Rear View
wire
exit &
drain
hole
A
A
A A
1/4" INTERNAL
TOOTH LOCK
WASHER
IMPORTANT: For drainage purposes, the speaker must be oriented so the wire
passage/drain hole is in the “6 o’clock” position (closest to the road). Improper
mounting will result in premature driver failure and void the product warranty.
IMPORTANT: The SA315 mounting kit comes with 3 long bolts (1/4-20 X 1-1/2” Hex Head). The longer
bolts are necessary to go through the mounting bracket, siren housing and into the siren driver. They
will replace 3 of the 4 shorter bolts (“A”) now secure the driver to the speaker housing.
short bolt be used in the
hole that go through the bracket so it will properly secure the driver to the housing.
If you need to move the location of any of the short bolts try not to remove all of them at
once . If you do
need to remove all 4 bolts at once be sure to hold the driver securely in place.
must
does not
since there will be nothing to hold the siren driver to the speaker housing
which Your
speaker is shipped with 1 or more of the short bolts installed. A
Mounting the speaker to the bracket:
1/4 - 20 X 1-1/2"
HEX HEAD SS
(Speaker & Bracket)
1/4 - 20 X 1-1/2"
HEX HEAD SS
(Speaker & Bracket)
1/4" INTERNAL
TOOTH LOCK WASHER
1/4
(Speaker & Bracket)
- 20 X 1-1/2"
HEX HEAD SS
1/4 X 20 X 1-1/4 HEX HEAD
(Speaker Only)
1/4 X 20 X 1-1/4 HEX HEAD
(Speaker Only)
1/4 X 20 X 1-1/4 HEX HEAD
(Speaker Only)
1/4 - 20 X 1-1/2
HEX HEAD SCREW
1/4" INTERNAL
TOOTH LOCKWASHER
Fig. 4
CAUTION
Loud siren noise can cause
hearing damage and/or loss.
Refer to OSHA Section 1910.95 prior
to putting ANY siren into service!
Wear
Protection!
ACTIVATION OF THIS
SIREN MAY DAMAGE
UNPROTECTED EARS!
IMPORTANT! It is the responsibility of the
installation technician to make sure that the
installation and operation of this product will
not interfere with or compromise the
operation or efficiency of any vehicle
equipment! IMPORTANT! Before returning the
vehicle to active service, visually confirm the
proper operation of this product, as well as all
vehicle components/equipment.
DANGER!
Sirens produce extremely loud emergency warning tones! Exposure
to these tones without proper and adequate hearing protection, could cause ear
damage and/or hearing loss! The Occupational Safety & Health
Administration (www.osha.gov) provides information necessary to
determine safe exposure times in Occupational Noise Exposure Section
1910.95. Until you have determined the safe exposure times for your
specific application, operators and anyone else in the immediate
vicinity should be required to wear an approved hearing protection
device. FAILURE TO FOLLOW THIS RECOMMENDATION COULD
CAUSE HEARING LOSS!
1/4 - 20 X 1-1/2
HEX HEAD SCREW
1/4" INTERNAL
TOOTH LOCKWASHER
Fig. 4
CAUTION
Loud siren noise can cause
hearing damage and/or loss.
Refer to OSHA Section 1910.95 prior
to putting ANY siren into service!
Wear
Protection!
ACTIVATION OF THIS
SIREN MAY DAMAGE
UNPROTECTED EARS!
IMPORTANT! It is the responsibility of the
installation technician to make sure that the
installation and operation of this product will
not interfere with or compromise the
operation or efficiency of any vehicle
equipment! IMPORTANT! Before returning the
vehicle to active service, visually confirm the
proper operation of this product, as well as all
vehicle components/equipment.
DANGER!
Sirens produce extremely loud emergency warning tones! Exposure
to these tones without proper and adequate hearing protection, could cause ear
damage and/or hearing loss! The Occupational Safety & Health
Administration (www.osha.gov) provides information necessary to
determine safe exposure times in Occupational Noise Exposure Section
1910.95. Until you have determined the safe exposure times for your
specific application, operators and anyone else in the immediate
vicinity should be required to wear an approved hearing protection
device. FAILURE TO FOLLOW THIS RECOMMENDATION COULD
CAUSE HEARING LOSS!