Whelen SA350MH User Manual

Page 2

Page 2

3.25" ± .060

4.625"

6.50"

.281" DIA. HOLE

(2) PLACES

90° APART

4.00"

BLACK PVC CONDUIT

WIRE LENGTH

10.00"

11.25"

FIG. 1

Crimp Tall Cradle

Over Wire Insulation.

Crimp Short Cradle

Over Bare Wire.

Strip Wire to

Approximately 1/8"

AMP 2-POSITION PIN CONNECTOR

SPACER SEAL (FIBER)

SUPPLIED WITH TIP

PAPER GASKET

SUPPLIED W/TIP

RUBBER SEAL

SUPPLIED W/TIP

IMPORTANT NOTE: When installing the speaker driver, make sure to keep the drainage hole

to the bottom. The drainage hole is located under the model identification tag.

Strip Wire to Approx. 3/8" and

Slip Bare Wire Inside Pin Barrel

Crimp Large Cradle

over Bare Wire

Crimp Small Cradle

over Wire Insulation

Pin Barrel

Deutsch Pin

Terminal

FIG. 2

DEUTSCH 2-POSITION PIN CONNECTOR

The model SA-350MH siren speaker is shipped without a
connector attached to the speaker wires. The reason for this is
that the wiring harness on the vehicle may be equipped with
either an AMP socket connector, or a Deutsch® socket
connector. A connector kit is included with the siren speaker
and contains all the parts necessary for use with either
connector

1. Locate the speaker wire on the vehicle wiring harness and

determine the kind of wiring harness used.

2. In the supplied connector kit, choose matching connector

and pins, and install onto speaker wires.

NOTE: Speaker wires can be inserted into the choosen
connector in either position since polarity is not important.

FIGURE 2. Crimp Deutsch pin to wire using Deutsch crimping
tool DTT-16-00.

FIGURE 3. Grasp wire with crimped on pin approximately one
inch behind the pin. Push pin all the way inside rear seal of
connector until a click is felt. A slight tug on the wire will confirm
that the pin is properly locked in place.

FIGURE 4. Once the two pins are in place inside the connector
housing, use a needle nose pliers to insert the orange wedge
inside the connector housing from the other end. The wedge will
have to be fitted inside the cavity below the 2 pins.

FIG. 3

Pin Position Numbers are on Side of Connector Housing

Rear Seal

FIG. 4

Pins

End View of Connector

Orange Pin Wedge

PART NUMBER
01-0860541-00

72-4010291-00
38-0220049-00
38-0220048-00
38-0220405-00
72-2160158-65
38-0220047-00
22-0410510-00
67-1361600150
43-0263146-00
26-0610158-00
07-263152-007
14-130219-06
39-1H00316-35
39-1H02014-35
39-0015982-00

DESCRIPTION

SPEAKER MODEL SA-350MH

SA 510-M1 TIP
RUBBER SEAL
SPACER SEAL / FIBER
PAPER GASKET
150 M SPEAKER BELL
METAL GASKET
TERMINAL CAPS
#16 BLACK 15“ W/RECEPTICLE
SIREN DRIVER
PVC TUBING #6 BLACK #P-105
ADAPTER BRACKET
1/4 - 20x3/8” PPH SWEDGE SCREW
PIN TERMINAL DEUTSCH®
2 POS DEUTSCH PIN HSG
SECONDARY LOCK DEUTSCH

#8 X ½” PHILLIPS PHSMS

ITEM

1
2
3
4
5
6
7
8
9

QTY

REF

1
1

REF

1
2
2
2
1
1
1

1
1

5/16 - 18 X 1/2" HEX HEAD CAP SCREW
5/16 SPLIT LOCKWASHER

17
18

1
1