Whelen 3PC0C0CD - Manual

Page 1
CAUTION! DO NOT LOOK DIRECTLY AT THESE LEDS WHILE THEY ARE ON.
MOMENTARY BLINDNESS AND/OR EYE DAMAGE COULD RESULT!
IMPORTANT WARNING!
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
Installation:
1. Drill a 3/8” mounting hole and insert the mounting bolt
through the hinge bracket and into the mounting hole.
2. Secure the hinge bracket with the supplied elastic stop nut
and flat washer.
3. Extend the wires to your power source (6, 9 or 12 LED
White or Red: +12VDC Black: Ground). Fuse the power
wire at 3 amps.
WARNING! All customer supplied wires that connect to the
positive terminal of the battery must be sized to supply at
least 125% of the maximum operating current and FUSED at
the battery to carry that load. DO NOT USE CIRCUIT
BREAKERS WITH THIS PRODUCT!
Caution:
Permanent mounting of this product will require
drilling. It is absolutely necessary to make sure that no other
vehicle components could be damaged by this process.
Check both sides of the mounting surface before starting. If
damage is likely, select a different mounting location.
©2008 Whelen Engineering Company Inc.
Form No.14165 (011008)
Automotive:
Li
ght
hea
d
s
Installation Guide:
PAR-36 Super-LED® Work Light
®
ENGINEERING COMPANY INC.
Internet: www.whelen.com
Sales e-mail: [email protected]
Canadian Sales e-mail: [email protected]
Customer Service e-mail: [email protected]
For warranty information regarding this product, visit www.whelen.com/warranty
3/8-16 X 2-1/4
HEX HEAD
BOLT
MOUNTING
SURF
ACE
3/8-16
ELASTIC
STOP NUT
PAR 36
3/8" FLAT
WASHER
3/8"
FLAT
WASHER
3/8-16
ELASTIC
STOP NUT
HINGE
BRACKET
3/8-16
X 1-3/4"
CARRIAGE
BOLT
IMPORTANT! It is the
responsibility of the
installation technician to
make sure that the
installation and operation
of this product will not
interfere with or
compromise the operation
or efficiency of any vehicle
equipment! Before
returning the vehicle to
active service, visually
confirm the proper
operation of this product,
as well as all vehicle
components/equipment.
CAUTION! DO NOT LOOK DIRECTLY AT THESE LEDS WHILE THEY ARE ON.
MOMENTARY BLINDNESS AND/OR EYE DAMAGE COULD RESULT!
IMPORTANT WARNING!
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
Installation:
1. Drill a 3/8” mounting hole and insert the mounting bolt
through the hinge bracket and into the mounting hole.
2. Secure the hinge bracket with the supplied elastic stop nut
and flat washer.
3. Extend the wires to your power source (6, 9 or 12 LED
White or Red: +12VDC Black: Ground). Fuse the power
wire at 3 amps.
WARNING! All customer supplied wires that connect to the
positive terminal of the battery must be sized to supply at
least 125% of the maximum operating current and FUSED at
the battery to carry that load. DO NOT USE CIRCUIT
BREAKERS WITH THIS PRODUCT!
Caution:
Permanent mounting of this product will require
drilling. It is absolutely necessary to make sure that no other
vehicle components could be damaged by this process.
Check both sides of the mounting surface before starting. If
damage is likely, select a different mounting location.
©2008 Whelen Engineering Company Inc.
Form No.14165 (011008)
Automotive:
Light
hea
d
s
Installation Guide:
PAR-36 Super-LED® Work Light
®
ENGINEERING COMPANY INC.
Internet: www.whelen.com
Sales e-mail: [email protected]
Canadian Sales e-mail: [email protected]
Customer Service e-mail: [email protected]
For warranty information regarding this product, visit www.whelen.com/warranty
3/8-16 X 2-1/4
HEX HEAD
BOLT
MOUNTING
SURF
ACE
3/8-16
ELASTIC
STOP NUT
PAR 36
3/8" FLAT
WASHER
3/8"
FLAT
WASHER
3/8-16
ELASTIC
STOP NUT
HINGE
BRACKET
3/8-16
X 1-3/4"
CARRIAGE
BOLT
IMPORTANT! It is the
responsibility of the
installation technician to
make sure that the
installation and operation
of this product will not
interfere with or
compromise the operation
or efficiency of any vehicle
equipment! Before
returning the vehicle to
active service, visually
confirm the proper
operation of this product,
as well as all vehicle
components/equipment.