Whelen VTX609A - Manual

2. Select the mounting location for the Vertex, keeping in mind the following:
3. Choose a surface in the rear or bottom of the housing which is as flat as possible. Using a
hole saw, cut a 1” hole in the housing as shown (Fig. 1 & 2) and de-burr the hole.
4. Insert the LED lamp assembly into the reflector housing. Mark the location for the two
mounting holes (3/32” dia.). Remove the lamp assembly and drill the holes.
5. Install the lamp assembly and gasket using the #4 sheet metal screws, installation disc and
flat washers as shown to secure the lamp to the reflector assembly.
7. Remount both headlight assemblies to the vehicle and route the connector cables to their
designated control switches (power and Scan-Lock™).
8. The lamp driver should now be secured to the vehicle using the double-sided adhesive
tape provided.
● The Vertex may share the same reflector as the headlight, brake light, or signal light.
Make sure the Vertex does not interfere with the operation of these lights.
WARNING! Over-
tightening these screws could damage the Vertex™ and/or housing assembly. Do
not continue to tighten once the Vertex is secured against the housing.
●
● The Vertex must not be installed above the horizontal centerline of the reflector.
The Vertex must not be installed above any OEM-supplied light.
Top view of automotive composite
headlight or taillight housing.
Insert the Vertex from the back
or bottom of the headlight or rear
taillight housing, as close to the
focal point as possible.
NOTE:
Lamp Filament
is the focal
point of
the reflector.
®
ENGINEERING COMPANY INC.
51 Winthrop Road
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
Sales Email:[email protected]
Canadian Sales:[email protected]
Customer Service:[email protected]
www. .com
Vertex™ Series Super-LED® Light
Safety First: This document provides all the necessary information to allow your Whelen product to be properly and safely installed. Before beginning the installation
and/or operation of your new product, the installation technician and operator must read this manual completely. Important information is contained herein that could
prevent serious injury or damage.
Standard Mount (composite headlight or taillight housing) Installation:
1. Follow manufacturers instructions to remove the headlight (or taillight) reflector
assembly from the vehicle.
IMPORTANT NOTE: If the Vertex is being used in an area previously occupied by an
S30HA light assembly, it is important to seal the mounting holes used by the previous
assembly with RTV or other suitable material.
Flange Mount Installation:
All customer supplied wires that connect to the positive terminal of the battery must be
sized to supply at least 125% of the maximum operating current and FUSED at the
battery to carry that load. DO NOT USE CIRCUIT BREAKERS WITH THIS PRODUCT!
RED: Positive -
BLACK: Ground -
GREEN: SYNC -
WHITE: Scan-Lock™ -
IMPORTANT WARNING: DO NOT ATTEMPT TO USE THE VERTEX WITHOUT THE LAMP
DRIVER MODULE CONNECTED.
TO CHANGE PATTERNS:
TO CHANGE THE DEFAULT PATTERN:
TO RESTORE THE FACTORY DEFAULT PATTERN:
Flash Patterns -
Using the dimensions shown, drill appropriately sized wire access and mounting holes. Refer
the "FLANGE MOUNT" illustration shown for proper assembly order and secure the Vertex
using the hardware provided. R
and secure the lamp driver to the vehicle using the double-sided
tape provided.
The Vertex is powered & controlled by the 4-wire cable coming from the light assembly. Their
functions are as follows:
Extend the RED wire to a +12VDC power source (fuse @ 3 amps).
Extend the BLK wire to the negative terminal of the battery.
Connect the GRN wire to other SYNC capable devices to synchronize their
output. Cap off this wire if it is not used.
Extend the WHT wire to a customer supplied momentary switch (fuse
@ 1 amp). See Scan-Lock section for operation.
In order to program flash patterns, the lighthead must be on. With the appropriate lighthead(s)
activated:
To advance to the next available pattern apply +12VDC to the
WHT wire for less than 1 second and release. To cycle back to the previous pattern apply
+12VDC to the WHT wire for more than 1 second and release.
When the desired pattern is displayed, allow it to run
for more than 5 seconds. The lighthead will now display this pattern when initially activated.
This will reset all patterns back to their
default settings. With the light turned off, apply power to the WHT wire. With power applied to
the WHT wire, turn light on. Allow the unit to run for 3 seconds before removing power from the
WHT wire.
A normally open momentary switch should be used to control Scan-Lock operation.
The following is a list of all the available flash patterns:
oute the connector cables to their designated control switches
(power and Scan-Lock™)
Wiring & Operation:
Scan-Lock
Fig. 1
For warranty information regarding this product, visit www.whelen.com/warranty
©2008 Whelen Engineering Company Inc.
Form No. 14208D (021313)
1. SignalAlert™75 PH.1
2.
3.
4.
5.
6.
7. SignalAlert 75 PH.2
CometFlash®75 PH.1
CometFlash 75 PH.2
DoubleFlash 75 PH.1
DoubleFlash 75 PH.2
SingleFlash 75 PH.1
8.
9.
10.
11.
12.
13.
14. SingleFlash 75 PH.2
ComAlert™ PH.1
ComAlert PH.2
LongBurst™ PH.1
LongBurst PH.2
PingPong™ PH.1
PingPong PH.2
15.
16.
17.
18.
19.
20.
21.
22.
23.
24
25. SingleFlash 60
SingleFlash 90
SingleFlash 120
SingleFlash 300
DoubleFlash 150
ComAlert 150
ActionFlash™1
ActionFlash 2
ModuFlash™
. ActionScan™
Steady
SYNC Patterns Non-SYNC Patterns
Phase 1 (PH.1) flashes with PH.1 simultaneously
Phase 2 (PH.2) flashes with PH.2
PH.1 with PH.2
simultaneously
alternates
Phase Operation
Mounting
Surface
1.25"
3/32"
DIA.
Mounting Dimensions
Mounting Dimensions
FLANGE MOUNT
STANDARD MOUNT
1” DIA.
1.874"
3/32"
DIA.
1” DIA.
1
2
3
4
Mounting
Surface
Lamp Driver
Lamp Driver
2
5 4
3 1
1.
2.
3.
4.
RED
BLK
GRN
WHT
RED
BLK
GRN
WHT
#4 x 3/8" PPHSMS
Flange
Vertex
Gasket
- Power
- Ground
- SYNC
- Scan-Lock (FUSE @ 3A)
(FUSE @ 1A)
- Power
- Ground
- SYNC
- Scan-Lock (FUSE @ 3A)
(FUSE @ 1A)
1.
2. Gasket
Vertex 3.
4.
5. Installation Disc
#4 Flat Washer
#4 x 5/8" PPHSMS
• Proper installation of this product requires the installer to have a good understanding of
automotive electronics, systems and procedures.
• If mounting this product requires drilling holes, the installer MUST be sure that no vehicle
components or other vital parts could be damaged by the drilling process. Check both
sides of the mounting surface before drilling begins. Also de-burr any holes and remove
any metal shards or remnants. Install grommets into all wire passage holes.
• Do not install this product or route any wires in the deployment area of your air bag.
Equipment mounted or located in the air bag deployment area will damage or reduce the
effectiveness of the air bag, or become a projectile that could cause serious personal
injury or death. Refer to your vehicle owner's manual for the air bag deployment area. The
User/Installer assumes full responsibility to determine proper mounting location, based
on providing ultimate safety to all passengers inside the vehicle.
• For this product to operate at optimum efficiency, a good electrical connection to chassis
ground must be made. The recommended procedure requires the product ground wire to
be connected directly to the NEGATIVE (-) battery post.
• If this product uses a remote device to activate or control this product, make sure that this
control is located in an area that allows both the vehicle and the control to be operated
safely in any driving condition.
• Do not attempt to activate or control this device in a hazardous driving situation.
• This product contains either strobe light(s), halogen light(s), high-intensity LEDs or a
combination of these lights. Do not stare directly into these lights. Momentary blindness
and/or eye damage could result.
• Use only soap and water to clean the outer lens. Use of other chemicals could result in
premature lens cracking (crazing) and discoloration. Lenses in this condition have
significantly reduced effectiveness and should be replaced immediately. Inspect and
operate this product regularly to confirm its proper operation and mounting condition. Do
not use a pressure washer to clean this product.
• W
• FAILURE TO FOLLOW THESE PRECAUTIONS AND INSTRUCTIONS COULD RESULT IN
DAMAGE TO THE PRODUCT OR VEHICLE AND/OR SERIOUS INJURY TO YOU AND YOUR
PASSENGERS!
ARNING! All customer supplied wires that connect to the positive (+) terminal of the
battery must be sized to supply at least 125% of the maximum operating current and
“at the battery” to carry that load. DO NOT USE CIRCUIT BREAKERS WITH THIS
PRODUCT!
FUSED