Whelen 70C00VCR - Manual (Page 3)

Page 3
Scan-Lock™ (White/Violet)
WARNING: Pattern selection requires the LEDs to be turned on. Do not
look directly at the LEDs while the unit is on.
TO CHANGE PATTERNS: Apply +VBAT to the WHITE/VIOLET wire for less
than 1 second and release to cycle forward to the next available pattern.
Apply +VBAT to the WHITE/VIOLET wire for more than 1 second and
release to cycle back to the previous pattern. Allow the pattern to run for
more than 5 seconds to set as the default pattern.
TO RESTORE FACTORY DEFAULT PATTERN: With the power to the
lighthead off, apply +VBAT to the WHITE/VIOLET wire. Now turn power to
the lighthead on. The factory default pattern should now be displayed.
A Normally Open momentary switch can be used to control Scan-Lock.
IMPORTANT SPLIT LED NOTE: This lighthead will not have a Scan-Lock™
wire. You will find 2 sets of programming pins protruding from the LED side
of the circuit board. Where the Scan-Lock instructions say “apply +12 volts to
the Scan-Lock wire”, short the pins out with a penny (or other electrical
conducting item). For a Split SMT LED lighthead, there will be 2 sets of
programming pins. Both sides can be programmed separately using the
same procedure as a regular LED lighthead.
Flash Patterns:
1. SignalAlert™ 75
2. SignalAlert 150
3. SingleFlash 375
4. SingleFlash 150
5. SingleFlash 75
6. SingleFlash 150
7. DoubleFlash 150
8. DoubleFlash 75
9. CometFlash® 75
10. ActionFlash™
11. ModuFlash™
12. ComAlert™
13. ActionScan™
14. SignalAlert Steady
15. Steady (Brake)
Brake Patterns:
1. SignalAlert Steady
2. Steady Brake
SYNC Patterns:
1. SignalAlert 75 (Sim.)
2. SignalAlert 75 (Alt.)
Arrow Patterns:
1. Seq. to Solid 150
2. Seq. to Solid 80 3. Seq. to Solid (Steady On - Fast)
4. Seq. to Solid (Steady On - Slow)
5. SignalAlert to Steady On
6. Steady On
Dual Color Patterns:
1. SingleFlash 680 (Alt.)
2. SingleFlash 240 (Alt.)
3. SingleFlash 120 (Alt.)
4. SingleFlash 150 (Sim.)
5. DoubleFlash 240 (Alt.)
6. DoubleFlash 120 (Alt.)
7. DoubleFlash 150 (Sim.)
8. CometFlash® 120 (Alt.)
9. CometFlash 120 (Sim.)
10. ActionFlash (Alt.)
11. ActionFlash (Alt. - Sim.)
12. ModuFlash (Alt.)
13. ModuFlash (Sim.)
14. SignalAlert 120 (Alt.)
15. SignalAlert 100 (Sim.)
16. ActionScan (Alt. - Sim.)
17. Action Single
18. CH.1 Steady-CH.2 SF120
19. CH.1 Steady-CH.2 Action Single
20. CH.1 Steady-CH.2 CometFlash
21. CH.1 Steady-CH.2 FastAction
See next page for parts listings.
ARROW
..........
...Ground
....Scan Lock
LED Color
Black (12V) or
Black-White (24V)
White-Violet
- ™
Positive (+)
NOTE: In some instances two
ground wires are shown for
reference. This is to show
both the 12 volt and 24 volt
models. The lighthead will
have either one or the other
depending on model.
..........Positive (+)
............................SYNC
...............Ground
SYNC
LED Color
Grey
Black (12V)
BRAKE-TAIL-TURN
....Brake Positive (+)
........Tail Positive (+)
...Ground
.....Scan Lock
Yellow /
Brown /
White (12V) or
White-Black (24V)
White-Violet
- ™
..........Positive (+)
...Ground
.....Scan Lock
TURN
LED Color
Black (12V) or
Black-White (24V)
White-Violet
- ™
.......Positive (+)
.......Positive (+)
........................Ground
SPLIT
LED Color 1
LED Color 2
Black
MAX BIAS
..........Positive (+)
...Ground
LED Color
Black (12V) or
Black-White (24V)
FLOOD or BACK-UP
..................Positive (+)
...Ground
White
Black (12V) or
Black-White (24V)
..........Positive (+)
..Ground
......Scan Lock
WIDE ANGLE
LED Color
Black (+12V) or
Black-White (24V)
White-Violet
- ™
2 3 4
12 58 64
26
14
45
16
34
18
36
20
38
28
40
29
13 59 65
44
15
33
17
35
19
37
27
1
10 11 39 9
7 8 5 6
21 23 25 41 43 22 24 30 42 46 61 50 63 49 62 57 66
47 51 53 54 48 52 55 56
Housing (w/studs):
Housing:
Mounting Hardware & Gasket: 11-483530-011
11-483530-111
01-0483596-00
For use with:
HALOGEN, STROBE
or LED lightheads
Lighthead Housing:
Drivers Side:
Passengers Side:
01-0462735-01
01-0462736-01
For use with:
HALOGEN, STROBE
or LED lightheads
Surface Mount Housing:
Black:
Chrome:
01-0464758-00
01-0464758-01
For use with:
HALOGEN, STROBE
or LED lightheads
For use with:
HALOGEN, STROBE
or LED lightheads
Available Mounting Options
Wiring Options
Parts
Housing:
Housing w/Studs:
Mounting Hardware & Gasket: 11-463255-011
11-463255-111
01-0463331-00
Mini-Grill-Master Housing:
Black:
Chrome:
01-0483777-01
01-0483777-02
For use with: STROBE
or LED lightheads
For use with: LED lightheads
Flange Kit: Without Seal
With Seal
01-0462920-00
01-0462920-01
Swivel Mount Kit:
Black:
Chrome:
11-481138-00
01-0441293-00
32
67