Whelen 600 Series LED Scenelight - Manual

Page 1
CAUTION! DO NOT LOOK DIRECTLY AT THESE LEDS WHILE THEY ARE ON.
MOMENTARY BLINDNESS AND/OR EYE DAMAGE COULD RESULT!
IMPORTANT WARNING!
©2008 Whelen Engineering Company Inc.
Form No.14173B (051911)
Automotive:
Li
ghtheads
Installation Guide:
600 Series LED Scenelight
®
ENGINEERING COMPANY INC.
Internet: www.whelen.com
Sales e-mail: [email protected]
Canadian Sales e-mail: [email protected]
Customer Service e-mail: [email protected]
For warranty information regarding this product, visit www.whelen.com/warranty
Mounting:
IMPORTANT! When selecting a mounting location, keep in
mind that there must be a minimum of 2” clearance around
the perimeter of the lighthead and any vehicle components
(insulation, etc.). The rear of the lighthead must have a
minimum 1/8" clearance. This increases airflow over the
heatsink and helps maintain proper operating temperature.
Caution: Permanent mounting of this product will require
drilling. It is absolutely necessary to make sure that no other
vehicle components could be damaged by this process.
Check both sides of the mounting surface before starting. If
damage is likely, select a different mounting location.
1. Mark off the 4 mounting holes and the “cut-out” area as shown in the
mounting diagram.
2. Using a 1/4” drill bit, drill the 4 mounting holes then carefully cut and
remove the area of the mounting surface indicated. Do not remove
the mounting surface where the mounting holes are drilled.
3. Insert the screw grommet flange into the 4 holes drilled in step 2.
4. Route the cable to your power source and refer to “wiring
information” for connections and fusing. After testing the lighthead,
position it onto the mounting surface and secure it to the vehicle
using the four #6 x 1-3/4” sheet metal screws provided.
WARNING! All customer supplied wires that connect to the
positive (+) terminal of the battery must be sized to supply at
least 125% of the maximum operating current and FUSED “at
the battery” to carry that load. DO NOT USE CIRCUIT
BREAKERS WITH THIS PRODUCT!
IMPORTANT! It is the responsibility of the installation
technician to make sure that the installation and operation of
this product will not interfere with or compromise the
operation or efficiency of any vehicle equipment!
IMPORTANT! Before returning the vehicle to active service,
visually confirm the proper operation of this product, as well
as all vehicle components/equipment.
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
CAUTION! DO NOT LOOK DIRECTLY AT THESE LEDS WHILE THEY ARE ON.
MOMENTARY BLINDNESS AND/OR EYE DAMAGE COULD RESULT!
IMPORTANT WARNING!
©2008 Whelen Engineering Company Inc.
Form No.14173B (051911)
Automot
ive:
Li
ghtheads
Installation Guide:
600 Series LED Scenelight
®
ENGINEERING COMPANY INC.
Internet: www.whelen.com
Sales e-mail: [email protected]
Canadian Sales e-mail: [email protected]
Customer Service e-mail: [email protected]
For warranty information regarding this product, visit www.whelen.com/warranty
Mounting:
IMPORTANT! When selecting a mounting location, keep in
mind that there must be a minimum of 2” clearance around
the perimeter of the lighthead and any vehicle components
(insulation, etc.). The rear of the lighthead must have a
minimum 1/8" clearance. This increases airflow over the
heatsink and helps maintain proper operating temperature.
Caution: Permanent mounting of this product will require
drilling. It is absolutely necessary to make sure that no other
vehicle components could be damaged by this process.
Check both sides of the mounting surface before starting. If
damage is likely, select a different mounting location.
1. Mark off the 4 mounting holes and the “cut-out” area as shown in the
mounting diagram.
2. Using a 1/4” drill bit, drill the 4 mounting holes then carefully cut and
remove the area of the mounting surface indicated. Do not remove
the mounting surface where the mounting holes are drilled.
3. Insert the screw grommet flange into the 4 holes drilled in step 2.
4. Route the cable to your power source and refer to “wiring
information” for connections and fusing. After testing the lighthead,
position it onto the mounting surface and secure it to the vehicle
using the four #6 x 1-3/4” sheet metal screws provided.
WARNING! All customer supplied wires that connect to the
positive (+) terminal of the battery must be sized to supply at
least 125% of the maximum operating current and FUSED “at
the battery” to carry that load. DO NOT USE CIRCUIT
BREAKERS WITH THIS PRODUCT!
IMPORTANT! It is the responsibility of the installation
technician to make sure that the installation and operation of
this product will not interfere with or compromise the
operation or efficiency of any vehicle equipment!
IMPORTANT! Before returning the vehicle to active service,
visually confirm the proper operation of this product, as well
as all vehicle components/equipment.
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078