Whelen L360BGB - Manual (Page 2)

Page 2
Note: orientation
of "WHELEN"
on plastic dome.
NOTE: orientation of
Cage Bars
NOTE: location of
Cable Exit Slot
on Base Plate
F a s t e x
Grommet
F a s t e x
Grommet
F a s t e x
Grommet
F i n
Tree
Clip
F i n
Tree
Clip
F i n
Tree
Clip
Installation: Permanent Mount
1. Remove the mounting gasket from the beacons base (if
present) and discard.
2. Install the 3 fin pine tree clips into the drain holes of the
beacons base by pushing them firmly into the 3 holes
indicated in figure 1.
3. Install the Fastex grommets into the 3, square mounting
holes in the bottom of the beacons base (Fig. 1).
4. Secure the base plate to the beacon base by screwing
the 3 sheet metal screws into the Fastex grommets you
installed in step 3.
NOTE: The way you re-assemble the beacon will
determine which way the beacon faces when
mounted to the vehicle. Take note in figure 1 as to
where the cable exit slot and cage bars should be
located when assembled correctly. If assembled
improperly, the cage will block the LED display and
front and rear flash patterns will be reversed.
5. Place the base plate (with beacon) onto the mounting
surface in the exact mounting location and mark the 4
mounting holes off onto the mounting surface.
6. Remove the base plate and drill the 4 mounting holes
into the mounting surface using an appropriately sized
drill for the #10 X 3/4” sheet metal screws.
7. Place the mounting gasket onto the mounting surface
lining up the mounting holes you drilled in step 5 with
the holes in the gasket.
8. Place the assembled beacon and base plate onto the
mounting surface lining up the mounting holes with the
holes in the base plateand secure the beacon to the
surface with the #10 X 3/4” sheet metal screws.
9. Insert the cage bars into the base plate as shown and
secure them with the set screws.
10. Extend the wires to your power source and refer to the
beacons manual for wiring and operation.
Installation: 1” NPT Pipe Mount:
1. Turn the beacon upside-down and remove the base
gasket from the base and discard it. Install the fastex
grommets into the 3, square mounting holes in the
bottom of the base.
2. Install the 3 fin pine tree clips into the drain holes of the
base by pushing them firmly into the 3 holes (Fig. 1).
3. Feed the beacon wires through the base plate and secure
the base plate to the beacon base, by screwing the 3 sheet
metal screws into the Fastex grommets you installed in
step 3. (See re-assembly note in step 3 perm. mount)
4. Feed the beacon wires through the pipe then screw the
beacon onto the pipe, being careful not to pinch or strain
the wires. Hand tighten the unit onto pipe.
5. Extend the wires to your power source and refer to the
beacons manual for wiring and operation.
Fig. 1
#8/#10 FASTEX
GROMMET
(QTY 3)
#10-24 X 3/8"
PPHMS SS
(QTY 4)
360 LED BEACON
BLACK:
AS CAST:
BASE PLATE
(QTY 1)
SILVER:
P/N 11-384208-019
P/N 11-384208-007
P/N 11-384208-000
#10 X 3/4"
PPHSMS SS
(QTY 4)
#10 X 3/4" PPHSMS
(QTY 3)
L360 SERIES
MOUNTING GASKET
(QTY 1)
P/N 38-0263992-00
#6-32 X 5/16
WIZ LOCK NUT
ZINC PLATED
REFERENCE:
SUPER-LED
L360 SERIES
CAGE BAR
BRANCH
GUARD
REFERENCE:
L360 BASE
Shown without
LED's & parts
for clarity.
PINE TREE CLIP
(QTY 3)
#6-32 x 1" PPHMS SS