Whelen B63M7AA - Manual (Page 3)

Page 3
REAR
FRONT
ST
AR
TS
HE
R
E
REAR
FRONT
STA
RT
S
H
ER
E
S
TA
RT
S
HE
RE
REAR
FRONT
REAR
FRONT
S
TA
RT
S
HE
RE
PHASE 1
C o u n t e r
ClockWise
ClockWise
PHASE 1
C o u n t e r
ClockWise
PHASE 2
PHASE 2
ClockWise
NOTE: A 12 volt model is shown here. In 24 volt models
sequences will start with 4 LEDs lit instead of 3 as shown
making the patterns appear to flow less smoothly.
9. Rotator 60
10. Rotator 60
11. Rotator 90
12. Rotator 90
13. Rotator 120
14. Rotator 120
15. Rotator 300
16. Rotator 300
17. Rotator Double 150
18. Rotator Double 150
19. Rotator Triple 300/75
20. Rotator Triple 300/75
21. Rotator Quad 300
22. Rotator Quad 300
23. Rotator ModuFlash
24. Rotator ModuFlash
25. Oscillator 75
26. Oscillator 75
27. Sweep 40
28. Sweep 40
29. Sweep 75
30. Sweep 75
31. Sweep 150
32. Sweep 150 clockwise
counter-clockwise
clockwise
counter-clockwise
clockwise
counter-clockwise
clockwise
counter-clockwise
Seq. / clockwise
Seq. / counter-clockwise
Seq. / clockwise
Seq. / counter-clockwise
Seq. / clockwise
Seq. / counter-clockwise
clockwise
counter-clockwise
Right
Left
Right
Left
Right
Left
Right
Left
REGULAR P
A
T
TERNS
Oscillator
Sweep
Starts on one side, circles completely around the
beacon, then circles back.
First half of beacon lights up on one side sweeping
to opposite side. Action repeats for other half
of beacon.
ST
A
R
T
1
Oscillator
2
Oscillator
ST
A
R
T
1
2
Sweep
END
END
Sweep
S
TA
RT
S
TA
RT
Scan-Lock™ / Flash Pattern Selection:
Activate the RED wire (or WHT/ORG for cruise mode) to turn on the
beacon.
To cycle forward through patterns activate the WHT/VIO wire for less
than 1 second and release.
To cycle backward through patterns activate the WHT/VIO wire for
more than 1 second and release.
When the desired pattern is displayed, allow it to run for more than 5
seconds. The beacon will now display this pattern when activated.
To reset to the factory default pattern turn off power, activate the WHT/
VIO wire, then turn power back on.
IMPORTANT! It is the responsibility of the installation technician to
make sure that the installation and operation of this product will not
interfere with or compromise the operation or efficiency of any
vehicle equipment! Before returning the vehicle to active service,
visually confirm the proper operation of this product, as well as all
vehicle components/equipment.
1. Rotator 75
2. Rotator 75
3. Rotator 75
4. Rotator 75
5. Rotator 150
6. Rotator 150
7. Rotator 150
8. Rotator 150 clockwise
clockwise
counter-clockwise
counter-clockwise
clockwise
clockwise
counter-clockwise
counter-clockwise
Phase 1
Phase 2
Phase 1
Phase 2
Phase 1
Phase 2
Phase 1
Phase 2 (Default Pattern)
Flash Patterns:
SYNC P
A
TTERNS
CAUTION! DO NOT LOOK DIRECTLY AT THESE LED’S WHILE THEY ARE ON.
MOMENTARY BLINDNESS AND/OR EYE DAMAGE COULD RESULT!
I M P O R TA N T W A R N I N G !