Whelen SLPMMAA - Manual (Page 2)

Page 2
NOTE: The swivel mounting bracket can also be
attached with the suction cup on the outside as
shown here.
For a permanent mount, use sheet metal screws
(not included) in place of the suction cups. Make
sure there is nothing that will be damaged on
the opposite side of the mounting area.
RAPIDFIRE 680
RAPIDFIRE 240
RAPIDFIRE 120
SIMULTANEOUS RAPIDFIRE
DOUBLEFLASH 240
DOUBLEFLASH 120
SIMULTANEOUS DOUBLEFLASH 150
COMETFLASH
SIMULTANEOUS COMETFLASH
ACTIONFLASH
SIMULTANEOUS ACTIONFLASH
MODUFLASH
SIMULTANEOUS MODUFLASH
SIGNALALERT 120
SIMULTANEOUS SIGNALALERT
SCANFLASH™
CALFLASH™
CALIF. STEADY w/ RAPIDFIRE™ 240
CALIF. STEADY w/ CalFlash
CALIF. COMETFLASH®
CALIF. ACTIONFLASH™
™
™
™
™ 150
®
®
™
™
™
™
™
™ 120
680 Single Flashes Per Minute (SFPM)
240 SFPM
120 SFPM
150 SFPM
240 Double Flashes Per Minute (DFPM)
120 DFPM
150 DFPM
120 Comet Flashes Per Minute (CFPM)
120 CFPM
2 Alternating 120 CFPM, 4 Alternating 240 SFPM
2 Alt. 120 CFPM, 4 Simul. 240 SFPM
120 to 360 SFPM
120 to 360 SFPM
120 Flashes Per Minute (FPM)
120 FPM
2 Cycles of Every Pattern
340 SFPM
240 DFPM
340 SFPM
120 CFPM
2 Alternating 120 CFPM, 4 Alternating 240 SFPM
Available Flash Patterns
CIGAR PLUG ASS'Y.
(Internal 8 Amp Fuse
& Rear On/Off Switch)
Extend RIBBED wire to GROUND ●
● Extend SMOOTH wire to switched
+12VDC and fuse @ 3 Amps
● Cut cigar plug adaptor off power cord
NOTE! (Model SLPMM**P Only)
SUCTION CUP
(MUSHROOM HEAD)
P/N 08-1522840-00
#6 INTERNAL TOOTH
LOCK WASHER
#6-32 X 1/4" PPHMS
SELF TAP TYPE F SS
360 SWIVEL BRACKET / BLACK
P/N 07-242731-001 º
SNAP-IN BRACKET / BLACK
P/N 07-242730-001
LENS, AMBER
LENS, BLUE
LENS, CLEAR
LENS, RED P/N 68-1942935-10
P/N 68-1942935-20
P/N 68-1942935-30
P/N 68-1942935-50
SLIDE
BRACKET
OUT
Optional Bail-type
Mounting bracket shown
for reference (P/N 01-0483814-00)
#6 x 1”
Mounting Screws
Qty. 4 (included with bracket)
Press pattern button for more than 1 second and release.
TO CYCLE BACKWARDS THROUGH ALL FLASH PATTERNS:
Hold the pattern button down and turn the SlimLighter
power on. Hold for more than 3 seconds and release.
TO RESET TO THE TOP OF THE PATTERN LIST:
While cycling through the patterns, allow a pattern
to run for more than five seconds, this will become
the default pattern until it is changed.
TO CHOOSE A FLASH PATTERN:
Press the pattern button for less than 1 second
and release. Repeat to go to the next pattern.
TO CYCLE FORWARD THROUGH FLASH PATTERNS:
PASSENGER
'S
SIDE
DRIVER'S
SIDE
Lens Removal
Insert awl or other
tool here and push
on retaining clip.
Passenger Side / Rear View
Flash Pattern
Opening
(Internal Button;
Use a pen or similar tool
to cycle through patterns )
®
TM
CHESTER, CT 06412
PATENT #6,317,052
WARNING! DO NOT LOOK DIRECTLY AT
THESE LEDS. MOMENTARY BLINDNESS
AND/OR EYE DAMAGE COULD RESULT!
IMPORTANT!
LENS REMOVAL:
NOTE:
It is easier to perform this operation
with the light laying face down on a table. Take an awl,
(or any suitable tool) insert it into the hole in the back of
the light and carefully push on the back of the retaining
clip, (while at the same time
pulling out on the swivel
mounting bracket) until the
clip clears the light housing
and you can slide the bracket
out and remove it. With the
bracket out, both the inner
and outer lens’ may be
removed for replacement.
If you replace the
lens on the side of the power
cord, make sure the cord is
in its wire channel before
re-attaching the suction cup
assembly.
All customer supplied wires that
connect to the positive (+) terminal of
the battery must be sized to supply at
least 125% of the maximum operating
current and fused at the battery to carry
that load.
CAUTION: This product has been designed
to rest on top of the vehicle’s dashboard.
Suction cups are used to prevent lateral
movement while the vehicle is in motion.
These suction cups should not be used to
suspend this product above the dashboard.