SAF-HOLLAND XL-TA10006OM Drum Brake Axles Tapered and Parallel Spindle Axles - Manual (Page 3)

3 XL-TA10006OM-en-US Rev B · 2014-03-13 · Amendments and Errors Reserved · © SAF-HOLLAND, Inc., SAF-HOLLAND, HOLLAND, SAF,
and logos are trademarks of SAF-HOLLAND S.A., SAF-HOLLAND GmbH, and SAF-HOLLAND, Inc.
Contents
Contents Page
Section 10 – Retracting the Brake Shoes or Slack
Adjuster Control Arm(s).................................. 16
Section 11 – Brake Shoe Removal ...................................... 17
Section 12 – Brake Shoe Installation .................................. 19
Section 13 – Brake Adjuster Removal ................................. 22
Section 14 – Brake Adjuster Installation ............................. 22
Section 15 – S-Camshaft and Bearing Removal Procedure ... 23
Section 16 – S-Camshaft and Bearing Installation .............. 24
Section 17 – Brake Adjustment Procedure .......................... 26
Section 18 – ABS Sensor Replacement Procedure ............... 27
Section 19 – Axle Alignment Inspection .............................. 27
Section 20 – Routine Service Schedule ............................... 28
Section 21 – Torque and Lubrication Specifications ............. 29
Section 22 – Troubleshooting Chart .................................... 30
Contents Page
Introduction ......................................................................... 3
Warranty .............................................................................. 3
Notes, Cautions, and Warnings ............................................. 3
Section 1 – General Safety Instructions ................................ 4
Section 2 – Model Identification........................................... 5
Section 3 – Identification Tag ............................................... 5
Brake Components Parts List Prior to November 30, 2012 ..... 6
Brake Components Parts List After November 30, 2012 ......... 7
Section 4 – Hubs, Bearings and Seal Removal ....................... 8
Section 5 – Bearing Inspection ........................................... 10
Section 6 – Hubs, Bearings and Seal Installation ................. 11
Section 7 – Hub Bearing Adjustment .................................. 13
Section 8 – Hub Cap Installation ........................................ 15
Section 9 – Filling Hub with Lubricant (Oil Based) .............. 15
Notes, Cautions, and Warnings
Before starting any work on the unit, read and understand all
the safety procedures presented in this manual. This manual
contains the terms “NOTE”, “IMPORTANT”, “CAUTION”, and
“WARNING” followed by important product information. These
terms are defined as follows:
NOTE: Includes additional information to enable accurate
and easy performance of procedures.
IMPORTANT: Includes additional information that
if not followed could lead to hindered
product performance.
Used without the safety alert symbol,
indicates a potentially hazardous
situation which, if not avoided, could
result in property damage.
Indicates a potentially hazardous
situation which, if not avoided, could
result in minor or moderate injury.
Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury.
Introduction
This manual provides the necessary information for the maintenance,
inspection, and safe operation of the SAF
® axle/brake system.
Read this manual before using or servicing this product and
keep it in a safe location for future reference. Updates to this
manual, which are published as necessary, are available on
the internet at www.safholland.us.
Use only SAF-HOLLAND ® Original Parts to service your
SAF-HOLLAND INTEGRAL™ disc brake axle. A list of technical
support locations that supply SAF-HOLLAND
® Original Parts
and an Aftermarket Parts Catalog are available on the internet
at www.safholland.us or contact Customer Service at 888-396-6501.
Warranty
Refer to the complete warranty for the country in which the
product will be used. A copy of the written warranty is included
with the product or available on the internet at www.safholland.us.