Sealey MC135 - Manual (Page 2)

 WARNINg! Ensure you read, understand and apply the safety instructions
before use.
 WARNINg! Before use, ensure the motorcycle to be lifted has a suitable
structure and centre of gravity to accommodate the lift platform without
damaging the bike.
DO NOT use if the lift will foul on the exhaust or other vulnerable parts.
Remove any lower fairing and ensure the bike is adequately secured to
the lift before operating.
4.1. Position the lift in a suitable area, checking that the surface on which the lift will
stand is solid and flat (preferably concrete).
4.2. Wheel bike over the lift so that the centre of gravity of the bike is over the
platform, which must fit snugly against the underside of bike.
4.3. By depressing the lift pedal, raise the platform up to the underside of the bike.
4.4. secure the bike to the platform using the adjustable ‘J hooks’ hooked into
the footpegs and secured to the anchor points on the platform. Ensure that
the bike will not move once the lift is in operation. should it not be possible to
secure the bike with the ‘J hooks’ use suitable strap(s) to secure the bike to the
platform.
4.5. Pump the lift pedal to raise the load.
4.6. When the lift is raised to the desired position insert the locking bar into the holes
on the frame (fig.3) so that the lift cannot be inadvertently lowered. there are
four possible positions in which to lock the lift; 490, 660, 780, & 895mm.
4.7. When work is complete, check under the lift to ensure that there are no
obstructions and that it is safe to lower the unit.
remove the safety bar from the frame and then SLOWLY press the release
valve pedal (fig.4) to GENTLY lower the lift.
IMPORTANT: speed of lowering is controlled by the release valve pedal.
the more the pedal is depressed the quicker the lift descends. Ensure the
descent is slow and controlled.
4.8. When the lift is fully lowered, ensure the bike is supported before removing the
‘J hooks’, and remove the bike from the lift.
4. OPERATINg INSTRUCTIONS
5.1. When the lift is not in use, it must be stored in the lowest position to minimise ram and piston corrosion.
5.2. Keep the lift clean and wipe off any oil or grease. Lubricate all moving parts with acid free oil.
5.3. Before each use check all parts. If any part of the lift is damaged or suspect remove lift from service and take necessary action to repair.
DO NOT use the lift if it is believed to have been subjected to abnormal load or shock. Inspect and take appropriate action.
5.4. Periodically check the ram and piston for signs of corrosion. clean exposed areas with a clean oiled cloth.
5.5. the hydraulic oil level is checked as follows:
1) Position the fully lowered lift on a level surface.
2) remove filler plug. correct oil level is to filler hole - add hydraulic oil as necessary.
 WARNINg! Only a good quality hydraulic oil, such as SEALEY HYDRAULIC OIL, must be used. DO NOT use brake fluid.
 IMPORTANT: Only fully qualified personnel should attempt maintenance or repair. Contact your authorised dealer.
5. MAINTENANCE
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE LIFT.
Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK.
DO NOT RETURN THE PRODUCT TO US. Please telephone us on 01284 757500 to obtain the address and phone number of your local
agent. If product is under guarantee please contact your dealer.
De-commissioning product
should the lift become completely unserviceable, draw off the oil into an approved container and dispose of the lift and the oil according to local
regulations.
fig.3
LOCkINg BAR
rELEAsE VALVE PEDAL
fig.4
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534 [email protected]
Sole Uk Distributor, Sealey group,
Kempson Way, suffolk Business Park ,
Bury st. Edmunds, suffolk,
IP32 7Ar
www.sealey.co.uk
Web
email
Original Language Version Mc135 Issue: 2 - 15/10/09