Sealey MCW360 - Manual

INSTRUCTIONS FOR:
MOTORCYCLE PORTABLE FOLDING WORKBENCH
360KG
MODEL NO:
MCW360
3 Ensure safety strap is securely fitted before moving workbench.
3 Select a work area suitable for the workbench and keep the area clean, tidy and free from unrelated materials. Ensure there is adequate
lighting.
3
Stand the workbench on a stable surface strong enough to take the weight of the workbench and the motorcycle.
3 Ensure that the motorcycle is secure and stable before beginning to work on it.
3 The maximum motorcycle weight is 360kg. DO NOT exceed this rated capacity.
3 Maintain the workbench in good condition.
3 Replace or repair damaged parts. Use recommended parts only, unauthorised parts may be dangerous and will invalidate the warranty.
3 Remove ill fitting clothing, remove ties, watches, rings and other loose jewellery and contain long hair.
3 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3 Keep children and unauthorised persons away from the work area.
 DO NOT attempt to ride a motorcycle up onto the workbench.
Lightweight, folding design with transportation wheels makes this work bench totally mobile for use anywhere. With a working height of 460mm, it
is ideal for servicing/maintenance. Additionally the loading ramp doubles as a convenient workshop stool. Folding design allows compact storage
where workshop space is limited. Suitable for professional workshops, mobile mechanics, enthusiasts, track days or as a display table in
showrooms.
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . .MCW360
Maximum Load Capacity:. . . . . . . . . . . . . . . . . . . 360kg
Maximum Height: . . . . . . . . . . . . . . . . . . . . . . . . 460mm
Platform Width/Length:. . . . . . . . . . . . . . 600 x 2200mm
Ramp Length:. . . . . . . . . . . . . . . . . . . . . . . . . . 1100mm
Folded Dimensions (L x W x D): . 1100 x 600 x 150mm
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38kg
4 .1 . Wheel workbench to its desired location.
4 .2 . With assistance lay the workbench on the ground, undo the safety strap and open the two halves out flat. The middle leg will deploy itself.
4 .3 . Remove the R clip from the pin on the middle of the leg brace. Remove the pin, see fig.1.
4 .4 . Fold out the leg perpendicular to the workbench and secure the leg brace using the pin and R clip, see fig.2.
4 .5 . Repeat operations 4.3. and 4.4. for the other leg.
4 .6 . With assistance, turn the workbench the right way up. Note: Take care that the loading ramp does not swing out whilst the workbench is being
turned the right way up.
4 .7 . Fold the loading ramp down.
4 .8 . Workshop Stool
4.8.1. Remove the R clips and pins which hold the loading ramp to the workbench, see fig.3.
4.8.2. Turn the loading ramp over and remove the R clip and pin to let the legs unfold. Turn the right way up.
1 . SAFETY
2 . INTRODUCTION
3 . SPECIFICATION
4 . OPERATION
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY . NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS . USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED . FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL
INJURY AND WILL INVALIDATE THE WARRANTY . KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE .
fig.2
fig.1
Original Language Version
MCW360 Issue: 1 - 29/08/14 © Jack Sealey Limited