Sealey PH250 User Manual
Instructions for, Model no's, Safety instructions
1.1.
ELECTRICAL SAFETY
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A
Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current
Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected
by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. The
Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a
qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The
Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators.
If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
See 1.1.1. and 1.1.2. and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none is loose.
1.1.6.
Important: Ensure that the voltage marked on the appliance matches the power supply to
be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7.
DO NOT pull or carry the appliance by the power cable.
1.1.8.
DO NOT pull the plug from the socket by the cable.
1.1.9.
DO NOT use worn or damaged cables, plugs or connectors.
Immediately have any faulty item repaired or replaced by a qualified electrician. When a
BS 1363/A UK 3 pin plug is damaged, cut the cable just above the plug and
dispose of
the plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends beyond the cable restraint and
that the restraint is tight.
Double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only. To
rewire, connect the wires as indicated above -
DO NOT connect either wire to the earth terminal.
1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure
that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket
with your electrician.
1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance
plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use
of 2.5mm² section cable.
InSTRUCTIonS FoR
:
POWER HOISTS - 250kG / 400kG
MoDEL no's:
PH250.V4 & PH400.V3
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND
CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE kEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.2.
GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
Familiarise yourself with the application, limitations and potential hazards of the hoist.
WARNING! Disconnect the hoist from the mains power before changing accessories, servicing or performing any maintenance.
Maintain the
hoist in good condition (use an authorised service agent).
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Locate hoist in a suitable work area, keep area clean and tidy and free from unrelated materials. Ensure that there is adequate lighting.
WARNING! Ensure that the mounting for the hoist is capable of supporting the rated capacity of the hoist (plus the weight
of the hoist) without failure and that the hoist is mounted horizontally.
Keep the hoist clean for best and safest performance and check moving parts alignment regularly.
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
Keep children and unauthorised persons away from the work area.
Ensure the load is correctly secured before operating the hoist.
Keep hands away from the cable reel when winding the hoist in.
DO NOT use the hoist for any purpose other than that for which it is designed.
DO NOT operate the hoist if any parts are damaged or missing as this may cause failure and/or possible personal injury.
DO NOT exceed the rated capacity of the hoist.
DO NOT adjust or tamper with the maximum lift cut-out mechanism.
DO NOT use the hoist out of doors.
DO NOT get the hoist wet or use in damp or wet locations or areas where there is condensation.
DO NOT allow untrained persons to operate the hoist.
DO NOT operate the hoist when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT use the hoist where there are flammable liquids, solids or gases such as paint solvents, etc.
DO NOT attempt to lift angled loads or to drag loads with the hoist. The centre of gravity of the load must always be directly below the hoist.
DO NOT allow the load to swing beneath the hoist.
DO NOT allow a raised and supported load to fall and thus shock load the mounting, hoist, cable and hook.
FUSE RATING:
PH250.V4 - 13 Amp
PH400.V3 - 13 Amp
Blue
Neutral
Wire
Yellow & Green
Earth Wire
Cable
Restraint
Brown
Live
Wire
Original Language Version
PH250.V4 & PH400.V3 Issue: 1 - 04/03/10