Sealey SAC3153B - Manual (Page 2)

A V-pump belt driven compressor, 150/200ltr, 3hp with bespoke front
control panel, with two outlets, one regulated and one direct. the
pump features heavy-duty fully cast cylinders, capped by alloy heads
for improved heat dissipation and long life. suitable for professional
workshop applications. Powered by a heavy-duty induction motor for
reliable operation. twin capacitors and a centrifugal switch aid
trouble free startup on a good *16amp supply. Precision welded
receiver tank manufactured to meet Pressure Vessel directive
2009/105/ec. fitted with fully automatic pressure cut-out switch, air
regulator, receiver and supply pressure gauges. supplied with handle
and wheels for easy manoeuvrability.
2. iNTROdUCTiON & SPECiFiCATiON 1.3. GENERAL SAFETY
3 familiarise yourself with the application and limitations of the
compressor.
3 ensure the compressor is in good order and condition before
use. If in any doubt do not use the unit and contact an
electrician/service agent.
 WARNiNG! Compressor must only be serviced by an
authorised agent. DO NOT tamper with, or attempt to
adjust, pressure switch or safety valve.
3 Before moving, or maintaining the compressor ensure it is
unplugged from the mains supply and that the air tank
pressure has been vented.
3 maintain the compressor in good condition and replace any
damaged or worn parts. use genuine parts only.
Unauthorised parts may be dangerous and will invalidate
your warranty.
3 read the instructions relating to any accessory to be used
with this compressor. ensure the safe working pressure of
any air appliance used exceeds compressors output
pressure. If using a spray a gun, check that the area selected
for spraying is provided with an air change/ventilation system.
3 ensure the air supply valve is turned off before disconnecting
the air supply hose.
3 to move the compressor use the handle only. maintain unit’s
centre of gravity when moving or lifting. dO NOT attempt to
lift or move the compressor by any other means.
3 use the compressor in a well ventilated area and ensure it is
placed on a firm surface.
3 Keep tools and other items away from the compressor when
it is in use, and keep area clean and clear of unnecessary
items.
3
ensure the air hose is not tangled, twisted or pinched.
3 Keep children and unauthorised persons away from the
working area.
7 dO NOT disassemble compressor for any reason. the unit
must be checked by qualified personnel only.
7 dO NOT use the compressor outdoors, or in damp, or wet,
locations.
7
dO NOT operate within the vicinity of flammable liquids,
gases or solids.
7 dO NOT touch compressor cylinder, cylinder head or pipe
from head to tank as these may be hot.
7 dO NOT use this product to perform a task for which it has
not been designed.
7 dO NOT deface the certification plate attached to the
compressor tank.
7 dO NOT cover the compressor or restrict air flow around the
unit whilst operating.
q dANGER! dO NOT direct the output jet of air towards
people or animals.
7 dO NOT operate the compressor without an air filter.
7 dO NOT allow anyone to operate the compressor unless
they have received full instructions.
7 dO NOT operate the compressor if you are tired, under the
influence of alcohol, drugs or intoxicating medication
 WARNiNG! If an electrical fuse blows, ensure it is
replaced with an identical fuse type and rating.
3 When not in use, store the compressor carefully in a safe,
dry, childproof location.
 WARNiNG! the air tank is a pressure vessel and the
following safety measures apply:
7 dO NOT tamper with the safety valve, dO NOT modify or
alter the tank in any way and dO NOT strap anything to the
tank.
7
dO NOT subject the tank to impact, vibration or to heat and
dO NOT allow contact with abrasives or corrosives.
3 drain condensation from tank daily.
MOdEL: .............................................................................SAC3153B
Motor output: .............................................................................3.0hp
voltage/phase: ..................................................................230V - 1ph
Rated supply: .............................................................................. *16A
Speed at pump (rpm):.................................................................1243
Noise level: ............................................................................96dB(A)
Air displacement: ......................................................13.4cfm-380l/m
Maximum free air delivery: .....................................10.95cfm-310l/m
Tank capacity: ............................................................................150ltr
Max pressure: ...............................................................145psi /10bar
Weight: ........................................................................................89kg
dimensions (W x d x H): .................................1210 x 600 x 970mm
trip reset button (4.3.7.)
Ball valve
MOdEL: .............................................................................SAC3203B
Motor output: .............................................................................3.0hp
voltage/phase: ..................................................................230V - 1ph
Rated supply: .............................................................................. *16A
Speed at pump (rpm):.................................................................1243
Noise level: ............................................................................96dB(A)
Air displacement: ......................................................13.4cfm-380l/m
Maximum free air delivery: .....................................10.95cfm-310l/m
Tank capacity: ............................................................................200ltr
Max pressure: ...............................................................145psi /10bar
Weight: ......................................................................................103kg
dimensions (W x d x H): ...............................1410 x 600 x 1020mm
fig.3
chocks
fully
inflated
1.5bar
1000mm
nominal
Wall
Original Language Version
sAc3153B/sAc3203B Issue no: 1 - 01/06/13 © Jack sealey limited 2013
fig.2
Pulley guard removed