Sealey LED120P - Manual (Page 2)

Original Language Version
3. instaLLation & use
2. introDuction & sPecification
Portable floodlight in die-cast powder coated aluminium housing with tubular
steel frame stand. State of the art LED Chip technology allows ultra bright
illumination whilst still keeping costs lower than traditional halogen bulbs. Even
spread of light across a 120° angle. Supplied with mains cable and BS
approved plug.
Power . . . . . . . . . . . . . . . . . . . . 20W
Lumen output. . . . . . . . . . . . 1200lm
Supply. . . . . . . . . . . . . . . . . . . . 230V
3.1. asseMbLy
3.1.1 Slide the high end of the stand into the black clamp as indicated in fig.3.
Align the threaded insert in the stand with the hole in the black clamp
and screw in the fixing knob ensuring that the contoured washer on the
threaded part fits the curvature of the clamp. Adjust the angle of the
floodlight as required and tighten the knob to grip the stand.
3.2. use of LiGHt.
p
WarninG! ensure the mains power supply is off prior to using the
floodlight.
3.2.1. Position the floodlight in the area that requires illumination.
3.2.2. This LED floodlight develops minimal heat and is not subject to the
same restrictions that apply to halogen lamps that become too hot to
touch. We do however recommend that the floodlight should not be
placed in cramped or restrictive situations and recommend the following
minimum distances between the light and any surface/object.
● 500mm minimum between the top of the light and any overhead
surface, or objects.
● 200mm between sides of light and end or side walls, surfaces or
objects.
● 1 metre minimum between the front of the light and any object to be
illuminated.
 WarninG! ensure the light is disconnected from the mains
power supply when not in use.
3.3. Maintenance.
● Clean the light with a dry, dust-free cloth. Do not use solvents or
abrasives to clean the light.
● If necessary clean the glass with alcohol and a soft cloth.
● Do not use the light without the glass shield.
● Although weather proof, the light must not be stored wet. Should the
unit become wet, unplug from mains and wipe dry before storing.
● Do not use the light without the weather seal intact.
● Repairs must only be undertaken by a qualified electrician.
1.3. GeneraL safety
p
WarninG! turn off the mains power supply before servicing or
performing any maintenance.
3 Ensure the light is installed correctly in accordance with these
instructions.
 If you use an extension lead the cable must be fully unwound from
the drum.
 DanGer! Do not direct the light into a person’s eyes. all models
have a very intense light output which, if incorrectly used, could
cause eye damage.
 Do not use the light without the front glass shield. Avoid touching the
glass shield as handling may reduce its serviceable life and cause the
glass to crack.
 Do not use the light without the weather seals intact.
 Do not use the light without the front glass shield.
 Do not use the light near flammable, combustible or explosive liquids,
solids, gases or equipment.
 Maintain the light in good condition. Repairs must only be undertaken
by a qualified electrician (use an authorised service agent).
 Keep a minimum distance of 1 metre from the front of light to the
surface which is to be illuminated.
 Locate the light in an adequate area for its function, keep area clean
and tidy and free from unrelated materials.
 When not in use, switch off the light and disconnect from the power
supply. Ensure that the unit is cool and dry and then store in a safe, dry,
childproof area.
 Do not install the light where it is likely to be knocked or hit.
 Do not install in bathrooms, shower rooms, sauna or such locations.
nOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
iMPortant: no liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
inforMation: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534 [email protected]
sole uK Distributor, sealey Group,
Kempson Way, Suffolk Business Park ,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email
LED120P Issue: 2 - 20/07/12
environmental Protection.
Recycle unwanted materials instead of disposing of them as waste.
All tools, accessories and packaging should be sorted, taken to a recycle centre and disposed of in a manner which is compatible
with the environment.
When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste
authority for recycling information.
fig.3
© Jack Sealey Limited
Parts support is available for this product. to obtain a parts listing and/or diagram, please log on to
www.sealey.co.uk, email [email protected] or phone 01284 757500.