Mobile to directed group call (dtmf, Entry outside the switch) – EFJohnson 3000 SERIES User Manual
Page 204

CALL SEQUENCES
B-4
5. When Mobile-1's transmit light is lit, enter DTMF
digits:
•
Enter 5-DTMF digits, 2 for Home channel and 3
for the Group ID desired.
•
Enter 8-DTMF digits, 3 for different site within
Switch, 2 for Home channel and 3 for Group ID
desired.
6. Release the PTT of Mobile-1 to indicate completion
of dialing.
•
O-CIM hears the “Confirmation Tone”.
•
Originating SNM (O-SNM) changes to SNM
Outgoing Task “8”.
•
Destination SNM (D-SNM) changes to Incoming
Seize Task “3”.
•
D-SNM changes to Incoming Task “4”.
•
Destination CIM (D-CIM) changes to Transmit
Task “3”.
•
D-SNM changes to Incoming Channel Task “5”.
•
O-SNM changes to Outgoing Channel Task “9”.
•
O-CIM changes to Ringing Task “D”.
•
Mobile-1 hears the “Call Proceed Tone”.
7. Press the PTT on Mobile-1.
•
O-CIM changes to Receive Task “4”.
•
D-CIM changes to Transmit Task “3”.
•
Mobile-2, destination mobile, hears Mobile-1
voice communication.
8. Release the PTT on Mobile-1.
•
O-CIM changes to Hang Task “7”.
•
D-CIM changes to Hang Task “7”.
•
Mobile-2 is silent.
9. Press the PTT on Mobile-2.
•
D-CIM changes to Receive Task “4”.
•
O-CIM changes to Transmit Task “3”.
•
Mobile-1 hears the voice of Mobile-2.
10.Release the PTT on Mobile-2.
•
D-CIM changes to Hang Task “7”.
•
O-CIM changes to Hang Task “7”.
•
Mobile-1 is silent.
11. Press the PTT on Mobile-1.
•
O-CIM changes to Receive Task “4”.
•
D-CIM changes to Transmit Task “3”.
•
Mobile-2 hears the voice of Mobile-1.
12.Press DTMF “#” key for longer than 1 second.
•
O-CIM changes to the End Call Task “E”.
•
Mobile-1 hears the “End Call Tone”.
•
O-CIM changes to Idle Task “2”.
•
Both SNMs change to the End Call Task “C”.
•
D-CIM changes to the End Call Task “E”.
•
Mobile-2 hears the “End Call Tone”.
•
D-CIM and both SNMs change to the Idle Task
“2”.
B.7 MOBILE TO DIRECTED GROUP CALL (DT-
MF ENTRY OUTSIDE THE SWITCH)
Use two mobiles defined to different Home and
Group ID.
NOTE: Some of these tasks change rapidly.
1. Mobile-1, the originating mobile, selects the Auxil-
iary Call group code.
2. Press the PTT of Mobile-1 to access the system.
•
Originating CIM (O-CIM), changes from Idle
Task “2” to Dial Tone Task “C”.
3. Release the PTT of Mobile-1.
•
Mobile-1 hears “Dial Tone” from the O-CIM.
4. Press the PTT of Mobile-1.
5. When Mobile-1's transmit light is lit, enter DTMF
digits:
•
Enter 5-DTMF digits, 2 for Home channel and 3
for the Group ID desired.
•
Enter 8-DTMF digits, 3 for different sites within
Switch, 2 for Home channel and 3 for Group ID
desired.