EFJohnson 3000 SERIES User Manual
Ii 3000 s, Set-up and alignment, Ulti
Table of contents
Document Outline
- TABLE OF CONTENTS
- SECTION 1 INTRODUCTION
- 1.1 SCOPE OF MANUAL
- 1.2 DEFINITIONS
- 1.2.1 TRUNKED SYSTEM
- 1.2.2 LTR TRUNKED SYSTEM
- 1.2.3 MULTI-NET TRUNKED SYSTEM
- 1.2.4 CONVENTIONAL SYSTEM
- 1.2.5 3000 SERIES SWITCH
- 1.2.6 CALL PROCESSOR
- 1.2.7 SYSTEM and SUBSCRIBER MANAGER
- 1.2.8 REPEATER SITE
- 1.2.9 HOME REPEATER CHANNEL
- 1.2.10 STATUS REPEATER CHANNEL
- 1.2.11 MONITOR REPEATER CHANNEL
- 1.2.12 TELEPHONE INTERCONNECT AND DATA TRANSMISSION
- 1.2.13 PUBLIC SWITCHED TELEPHONE NETWORK (PSTN)
- 1.2.14 PRIVATE AUTOMATIC BRANCH EXCHANGE (PABX)
- SECTION 2 3000 SERIES SWITCH
- SECTION 3 ARCHITECTURE
- SECTION 4 SYSTEM RACK
- 4.1 TWO SHELF 3000 SERIES SWITCH
- 4.1.1 POWER CONSUMPTION
- 4.1.2 EQUIPMENT REQUIRED
- 4.1.3 Two SHELF POWER SUPPLY
- 4.1.4 POWER SUPPLY REDUNDANT PLATE
- 4.1.5 VOLTAGE ADJUSTMENTS
- 4.1.6 REDUNDANT SUPPLY ADJUSTMENTS
- 4.1.7 VERIFY FAN AIR FLOW DIRECTION
- 4.1.8 VERIFY VOLTAGES ON POWER DISTRIBUTION CABLE
- 4.1.9 SYSTEM TEST PROCEDURE
- 4.1.10 FINAL CONFIGURATION VERIFICATION
- 4.2 FOUR SHELF 3000 SERIES SWITCH
- 4.2.1 POWER CONSUMPTION
- 4.2.2 EQUIPMENT REQUIRED
- 4.2.3 4-SHELF POWER SUPPLY
- 4.2.4 POWER SUPPLY REDUNDANT PLATE
- 4.2.5 VOLTAGE ADJUSTMENTS
- 4.2.6 REDUNDANT SUPPLY ADJUSTMENTS
- 4.2.7 VERIFY FAN AIR FLOW DIRECTION
- 4.2.8 VERIFY VOLTAGES ON POWER DISTRIBUTION CABLE
- 4.2.9 SYSTEM TEST PROCEDURE
- 4.2.10 FINAL CONFIGURATION VERIFICATION
- 4.3 SIX SHELF 3000 SERIES SWITCH
- 4.4 EIGHT SHELF 3000 SERIES SWITCH
- 4.1 TWO SHELF 3000 SERIES SWITCH
- SECTION 5 CALL PROCESSOR
- SECTION 6 NETWORK INTERFACE MODULE (NetNIM)
- SECTION 7 BASIC BOARD MODULE (BBM)
- SECTION 8 CHANNEL INTERFACE MODULE (CIM)
- SECTION 9 CONVENTIONAL CHANNEL MODULE (CCM)
- SECTION 10 DISPATCH CHANNEL MODULE (DCM)
- SECTION 11 DISPATCH INTERFACE MODULE (DIM)
- SECTION 12 INTELLIGENT DISPATCH MODULE (IDM)
- SECTION 13 SYSTEM NETWORK MODULE (SNM)
- SECTION 14 TELEPHONE INTERFACE MODULE (TIM)
- 14.1 DESCRIPTION
- 14.2 4-WIRE E&M INTERFACE DESCRIPTION
- 14.3 LED STATUS FOR E&M LEADS
- 14.4 E&M LEAD CIRCUIT THEORY OF OPERATION
- 14.5 TIM SETUP PROCEDURE
- 14.6 2WY SETUP AND ALIGNMENT PROCEDURES (-670)
- 14.7 2-WAY TIM ALIGNMENT PROCEDURES (-670)
- 14.8 DID SETUP AND ALIGNMENT (-660)
- 14.9 DID OPERATIONAL ALIGNMENT PROCEDURES (-660)
- 14.10 E&M SETUP AND ALIGNMENT (-680)
- 14.11 TERMSET MODULES
- 14.12 BACKGROUND INFORMATION
- 14.13 TUNING A DOD OR DID 2-WIRE INTERFACE TO THE 4-WIRE E&M BOARD.
- 14.14 BALANCING TO THE CENTRAL OFFICE
- 14.15 FCC USER INSTRUCTIONS AND CUSTOMER INFORMATION
- SECTION 15 VOTER DIAGNOSTICS MODULE (VDM)
- SECTION 16 POWER TERMINATION MODULE (PTM)
- SECTION 17 LOGGING ENCODER MODULE (LEM)
- SECTION 18 VOICE TONE MODULE (VTM)
- SECTION 19 WIDE AREA MODULE (WAM)
- SECTION 20 MULTI-NET CONSOLE MODULE (MCM)
- SECTION 21 CONVENTIONAL PATCH MODULE (CPM)
- SECTION 22 POWER SUPPLY
- SECTION 23 BACKPLANE
- SECTION 24 INTERCOM
- APPENDIX A ERROR MESSAGES
- APPENDIX B CALL SEQUENCES
- B.1 GROUP CALL
- B.2 DISPATCH CONSOLE (DC) TO MOBILE GROUP CALL
- B.3 MOBILE GROUP CALL TO DISPATCH CONSOLE
- B.4 MOBILE TO UNIQUE ID
- B.5 MOBILE TO UNIQUE ID FOR A MOBILE OUTSIDE SWITCH
- B.6 MOBILE TO DIRECTED GROUP CALL (DTMF ENTRY WITHIN SWITCH)
- B.7 MOBILE TO DIRECTED GROUP CALL (DTMF ENTRY OUTSIDE THE SWITCH)
- B.8 MOBILE ORIGINATED TELEPHONE CALL
- B.9 LANDSIDE (TIM) ORIGINATE TO MOBILE WITHIN SWITCH USING A DID LINE
- B.10 LANDSIDE (TIM) ORIGINATE TO MOBILE WITHIN SWITCH USING A 2WY LINE
- B.11 TIM ORIGINATE TO MOBILE OUTSIDE SWITCH USING A DID LINE
- B.12 LANDSIDE ORIGINATE TO MOBILE OUTSIDE SWITCH USING A 2WY LINE