ShoreLand'r LUV2314SW V.2 - Manual (Page 3)

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003808
Page 3 06/05/07
LUV2314SW (All Colors) Specifications:
Capacity: 2300 lbs.
GVWR: 2995 lbs.
GAWR: 2995 lbs.
Ship Wt: 575 lbs.
Frm Size: 2X4 (11 Ga)
Tire Size: ST215/75R14-C
Rim Size: 14 X 6 “J”
Brake: N/A
Coupler: 2”
Safety Chn: 7600 lb.
Suspension: 5 Leaf Hook Springs
Tongue Size: 3 X 5 X 65” Swing Tongue
FINAL ASSEMBLY INSTRUCTIONS
Remove the hardware bag from the frame, remove parts and sort
by size. Remove all the banded items from the frame.
TONGUE
Install the swing tongue by sliding it in the front of the tongue chan-
nel. Line the holes in the tongue with the holes in the tongue chan-
nel. Install the 1/2” x 4” hex bolt in the front cross hole and secure
with a 1/2” lock nut.
Remove the wire harness from the rear of the tongue. Place it
through the hole provided in the tongue cover plate.
Secure the tongue cover plate in position with the same 1/2” x 1-
1/2” hex bolt that secures the back of the tongue to the tongue
channel of the frame. Secure with a 1/2” lock nut. Tighten both bolts
just installed.
Plug the tongue wire harness into the frame harnesses by match-
ing colors and ends. Push the extra wire provided either into the
rear of the tongue or else remove the grommets in the side frame
and place the extra wire in the side frame. Replace grommets just
removed.
SAFETY CHAINS
Locate a 3/8” x1 1/4” hex bolt. Slip the bolt through a 3/8” flat wash-
er, then place through the last link of one of the safety chains.
Place the bolt with chain attached through the hole provided in the
bottom front of the tongue. Secure with a 3/8” flange lock nut. Tight-
en. Repeat on the other side and safety chain.
RETRACTABLE TIE DOWNS
Locate the two retractable tie downs. Next locate one of the 7/16”
x 1 ½” fine threaded bolts supplied with the retractable tie down.
Insert it into the bottom hole on the retractable tie down so the bolt
is pointing through the back side of the tie down. Insert the bolt
through the hole provided in the taillight bracket just inside the side
frame. Secure with the 7/16” flange lock nut. Tighten.
Repeat the above process on the other tie down.
WINCH POST ASSEMBLY
Your trailer may have come with the jack already installed on the
winch base. However, in the event that it did not, use the following
instructions to attach the jack to the winch base before it is installed
on the tongue.
ASSEMBLY AND MOUNTING INSTRUCTIONS:
JACK ON A PROFILE 2000 WINCH BASE
The Profile 2000 winch base used on the 2” x 4” and 2” x 5” frame
trailers is formed so that the jack can be mounted directly to it elimi-
nating the need for other mounting hardware for attaching the jack
to the tongue. The jack required for mounting does not require the
mounting base or any of the original mounting hardware compo-
nents.
Assemble as follows:
The jack must be mounted to the winch base before it is installed
on the trailer tongue. If the winch base is already mounted on the
tongue, it will have to be removed for the jack installation.
Locate the hardware bag and sort all items by size.
Lay the Profile 2000 winch base on its side so the side that the jack
ITEM PART # DESCRIPTION QTY NOTE
1 61395 COUPLER BAG WITH CHAINS 1
2 66494 PROFILE 2000 WINCH CASE ASSY 1
3 68271 TONGUE COVER PLATE 1
4 69268 FRAME WMENT 2X4X80W 190 LUND 1
5 69308 SWINGTONGUE ASSY 55IN NON BRAKE FG 1
6 69337 BUNK ASSY BUNDLE LUB29CBLW 2
7 0110059 HH 3/8-16 X 3 3/4 CS GR5 4
8 0110114 HH 1/2-13 X 4 CS GR5 1
9 0140094 HH 1/2-13 X 1 1/2 CS GR5 1
10 0210130 CARR 3/8-16 X 3 3/4 GR5 2
11 0210218 CARR 1/2-13 X 4 GR5 3
12 0810965 SCREW #10 X 1 1/2 SQ PAN SELF DRILL 2
13 1340030 LOCKWASHER 3/8 S/T MED ULTRASEAL 2
14 1340095 WASHER USS FLAT 3/8 2
15 1410109 HEX NUT 3/8-16 2
16 1440101 HEX LOCKNUT FLANGE 3/8-16 W/T&T 4
17 1440102 HEX LOCKNUT FLANGE 1/2-13 W/T&T 5
18 2400026 TIE DOWN RETRACTABLE 2
19 3510022 GROMMET 7/16IN MOLDED 1
20 3510030 GROMMET 7/8IN MOLDED 8
21 3510158 PLASTIC DRIVE RIVOT 4
22 3510253 LIGHT BEZEL - AMBER 2
23 3510368 TAILLIGHT STEP PAD TREAD TAPE 2
24 3510542 MOLDED REAR CROSSMEMBER PAD 2
25 3510597 GROMMET 13/16IN WITH SPLIT 9/16ID 2
- 4850414 DECAL LUND LARGE CHROME 2
- 4850417 DECAL LUND CHROME WING LARGE LEFT 1
- 4850418 DECAL LUND CHROME WING LARGE RIGHT 1
26 5110127 REFLECTOR ANDERSON AMBER 2
27 5110348 BO LICENSE PLATE BRACKET 1
- 5110561 HARNESS TONGUE 5WIRE FULL GROUND 1
- 5110565 HARNESS FRAME 214" FULL GROUND RT 1
- 5110566 HARNESS FRAME 214" FULL GROUND LT 1
28 5110569 TAILLIGHT RIGHT LED PETERSON 1
29 5110570 TAILLIGHT LEFT LED PETERSON 1
30 5110571 LIGHT CLUSTER THREE LED 1
31 5110572 MARINE YELLOW CLEARANCE LIGHT 2