Specifications, Network interface, Equipmentinterface – Verilink PRISM 4001 (34-00244) Product Manual User Manual
Page 6: Diagnostics, Configuration, Dial backup, Power, Mechanical, Environmental, Compatibility

General 1-2
PRISM 4001
• Simple setup and software management through
– a VT100-compatible terminal interface
– card-edge switches
– the 8100A Site Controller’s SNMP agent
• Programmable alarm thresholds
• Flash memory allows field software upgrades
Specifications
Network Interface
Service Types:
DDS-I Conforming to TR62310 and
TR41450
Operating Modes: Full Duplex, Point-to-Point, Multi-
Point
Line Rates:
2.4, 4.8, 9.6, 19.2, 38.4, and 56 kbps
64 kbps supported for LDM operation
Loop Range:
Up to 45 dB of loss
Timing Source:
Network, DTE, and Internal
Equipment Interface
Sync Data Rates:
2.4, 4.8, 9.6, 19.2, 38.4, 54, 56, 62, and
64 kbps
Async Data Rates: 2.4, 4.8, 9.6, 19.2, 38.4, and 57.6 kbps
Rate Adaptation:
Adapts subrate data port speeds to 56 or
64 kbps line rate
Anti-Stream Timer: Off, 10, 30, or 60 seconds
DTE Connection: DB-25 (PN 1051-2 25-pin) or V.35
Connector (PN 1051-3 34-pin). Selec-
tion depends on chassis model
Diagnostics
Status Indication:
Front panel LEDs
Terminal Interface on S
UPV
Port
T
ELNET
Session or SNMP Management
via T
XPORT
8100A Site Controller
Loopbacks:
CSU, V.54 (receive and send) Front
Panel Switch for Loop Activation
BERT:
511 Pattern
Configuration
Card Edge:
Four DIP Switches, two slide switches
S
UPV
Port:
Supervisory Port to Terminal Interface
Connection:
8-Pin Modular (RS-232)
Data Rates:
1.2, 2.4, 9.6, and 19.2 kbps
T
ELNET
Session:
Via 8100A Site Controller
SNMP Management
System:
Via 8100A Site Controller
All software configuration is non-volatile after
configuration is saved.
Dial Backup
Connection: RS-232,
10 -Pin
Modular
Backup Service:
PSTN or ISDN (External) Optional
14.4 Modem (Internal)
Configuration:
Information for backup unit is stored in
4001 and transmitted to backup unit by
Inband AT Commands
Dialing:
Numbers programmed and stored in
4001, and transmitted to backup unit by
in-band AT Commands
Restoral:
Manual or Automatic Restoral to leased
line service
Power
-48 VDC:
130 mA, 20 W, 73 BTU maximum
Mechanical
Mounting:
Fits TxPORT 1051 Chassis
Dimensions:
1.72" W, 6.8" H, 10.5" D (Unit)
17.2" W, 7" H, 10.5" D (Chassis)
Environmental
Operating Temp:
0
°
to 50
°
C (32
°
to 122
°
F)
Storage Temp:
-20
°
to 85
°
C (-4
°
to 185
°
F)
Humidity:
95% maximum, non-condensing
Compatibility
AT&T TR62310
AT&T TR41450
Industry Listings
FCC Compliance: Part 15 Subpart B, Class A and Part 68
NRTL:
UL 1459
CSA Certified:
Pending
IC/CSO3:
Pending
FCC Requirements
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment
is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and
if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communi-
cations. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user is
required to correct the interference at his own expense.
Shielded cables must be used to ensure compliance with the
Class A FCC limits.