Connections, Supv port connection, Table 2-s supv port connections – Verilink PRISM 4001 (34-00244) Product Manual User Manual
Page 15: Nms connection, Data port connections, Table 2-t dte rj-48 pinout, Table 2-u high-speed dte connector pinout, Connections -5
Installation 2-5
PRISM 4001
Connections
SUPV Port Connection
The front panel supervisory port serves two functions. A
modem may be connected to the SUPV port for remote
access or use of the COA (call on alarm) feature. The termi-
nal interface may be accessed through this port.
The SUPV port bit rate is set by configuration Switch Posi-
tion S3-3 and S3-4. The port is a serial RS-232 DCE port
configured for 8 bits, no parity, and 1 stop bit. The physical
connection is an 8-pin modular jack with the following
pinout (see Table 2 -S).
NMS Connection
The 4001 is fully compatible with the TxPORT 8100A Site
Controller. The 8100A is a manager that is installed in Slot
1 of the 1051 shelf. A single 8100A can manage up to fifty
4001s or a combination of TxPORT nest-mount units.
Data Port Connections
Both models of the TxPORT 1051 chassis provide connec-
tion to the customer equipment. Each slot of the 1051-2 has
a corresponding DTE 8-pin RJ-48 connector and a high-
speed DTE female 25-pin connector located on the chassis
rear panel. The 1051-3 chassis is similar except that it has a
high-speed DTE 34-pin connector instead of the 25-pin con-
nector. The pinout for the DTE RJ-48 connector is given in
Table 2-T and the pinout for the high-speed DTE connec-
tors is given in Table 2 -U.
Table 2-S SUPV Port Connections
Pin
SUPV Port
Terminal
Connection
1
DCD Out
2
CTS Out
3
Frame Ground
4
Data Out
5
Date In
6
Signal Ground
7
RTS In
8
DTR In
Table 2-T DTE RJ-48 Pinout
Pin
Signal
1
Data Out
2
Data Out
3
Not Used
4
Data In
5
Data In
6
Not Used
7, 8
Chassis Ground
Table 2-U High-Speed DTE Connector Pinout
ITU/EIA
Circuit
Common Name
DB-25
25-pin
V.35
34-pin
DCE
101/AA
Frame Ground
1
A
Gnd
102/AB
Signal Ground
7
B
Gnd
103/BA (A)
Transmit Data A
2
P
In
103/BA (B)
Transmit Data B
14
S
In
104/BB (A)
Receive Data A
3
R
Out
104/BB (B)
Receive Data B
16
T
Out
105/CA
Request to Send
4
C
In
106/CB
Clear to Send
5
D
Out
107/CC
Data Set Ready
6
E
Out
108/CD
Data Term Ready
20
H
In
109/CF
Data Carrier Detect
8
F
Out
114/DB (A)
Transmit Clock A
15
Y
Out
114/DB (B)
Transmit Clock B
12
AA
Out
115/DD (A)
Receive Clock A
17
V
Out
115/DD (B)
Receive Clock B
9
X
Out
113/DA (A)
External Clock A
24
U
In
113/DA (B)
External Clock B
11
W
In
141/LLB
Local Loopback
18
J
In
140/RLB
Remote Loopback
21
BB
In
142/TM
Test Mode
25
K
Out