Smithco Sweep Star V62 (sn 78191 – 78410) Parts & Service Manual - Manual (Page 49)

47
Accessories
78-206 CLEVIS HITCH PARTS LIST
REF# PART# DESCRIPTION QUANTITY
1 78-244 3 /
4
" Clevis 1
2 78-268 Hitch Insert 1
3 78-267 Tongue 1
HB-12-13-350 Bolt 1 /
2
- 13 x 3
1 /
2
1
HNTL-12-13 Lock Nut 1 /
2
- 13 1
4 HBFL-516-18-075 Flange Bolt 5 /
16
-18 x 3 /
4
4
HNFL-516-18 Flange Whiz Lock Nut 5 /
16
-18 4
5 78-299 Adjustment Slide 1
6 78-295 Adjustment Lock 2
15-020 Hand Grip 2
7 78-298 Control Panel Adjustment 1
8 78-312 Control Panel Mount 1
9 HSTP-14-20-075 Phillips Truss Machine Screw 1 /
4
- 20 x 3 /
4 (part of machine) 4
HNFL-14-20 Flange Whiz Lock Nut 1 /
4
-20 (part of machine) 4
10 HB-12-13-125 Bolt 1 /
2
- 13 x 1 1 /
4
4
HNTL-12-13 Lock Nut 1 /
2
- 13 4
11 HB-58-11-450 Bolt 5 /
8
- 11 x 4
1 /
2 (part of 78-244) 2
HNCL-58-11 Center Lock Nut 5 /
8
- 11 (part of 78-244) 2
INSTALLATION INSTRUCTIONS
Use two people to install hitches.
1. Block both wheels so machine does not roll.
2. Use the jack that is part of the sweeper to raise or lower sweeper to comfortable working height.
3. Slide the tongue (Ref 3) over the tabs on the front of the sweeper frame. Hitch must be on the outside.
Use the four 1 /
2
- 13 x 1 1 /
4
bolts (Ref 10) on the outside and four lock nuts on the inside. Tighten all four
bolts.
4. Install adjustment slide (Ref 5) to tongue (Ref 3) using the four flange bolts 1 /
4
- 20 x 3 /
4
and four flange
whiz lock nuts 1 /
4
- 20 (Ref 4).
5. Loosen adjustment locks (Ref 6) on control panel adjustment (Ref 7) and put control panel adjustment
onto the adjustment slide.
6. Tighten one adjustment lock (Ref 6).
7. Slide the control panel mount (Ref 8) through the control panel adjustment (Ref 7) and tighten the other
adjustment lock (Ref 6).
8. The control panel has all the hoses, wiring and throttle cable connected to it and to the sweeper. The
control panel is wrapped and fastened to the front of the sweeper.
9. Remove the control panel from the sweeper, bring it forward with the hoses to the rear and the throttle on
the left hand side.
10. Fasten the control panel to the control panel mount with the four truss head machine screws 1 /
4
- 20 x 3 /
4
and four flange whiz lock nuts 1 /
4
- 20 (Ref 9).
11. Put the two handles onto the valve and tighten the lock nuts with the handles pointing forward.
12. Place three hoses and the throttle cable on the left hand side of the adjustment slide.
Do not tow on public roads.