Smithco Sweep Star V62 (sn 78191 – 78410) Parts & Service Manual - Manual (Page 45)

43
Accessories
78-205 REMOTE VACUUM HOSE PARTS LIST
REF# PART# DESCRIPTION QUANTITY
1 HBFL-516-18-075 Flange Bolt 5 /
16
- 18 x 3 /
4
1
HNFL-516-18 Flange Whiz Lock Nut 5 /
16
- 18 1
2 78-318 Hose Rack 1
3 HBFL-516-18-075 Flange Bolt 5 /
16
- 18 x 3 /
4 (part of machine) 2
HNFL-516-18 Flange Whiz Lock Nut 5 /
16
- 18 (part of machine) 2
4 78-314 Remote Hose Connector 1
5 78-311 Handle Stop (part of machine) 1
6 18-340 Hose Clamp 2
7 8970-150 Vacuum Hose 8" x 150" 1
8 HB-14-20-150 Bolt 1 /
4
- 20 x 1 1 /
2
2
HNTL-14-20 Lock Nut 1 /
4
-20 2
9 78-350 Handle Holder 1
8803-17 Trim 1
10 78-354 Hose Handle 1
11 15-019 Round Grip 2
INSTALLATION INSTRUCTIONS
You will need two people and the tailgate open with an empty hopper. One person will have to be inside hopper.
Be sure engine is off. You will need an
11 /
32
and 9 /
32
drill.
1. Remove the two bolts (Ref 3) from the chute. Bolt the hose rack (Ref 2) in place using the two bolts you
removed from the chute. Using an 11 /
32
drill, drill through the hopper using the hose rack as a guide. Use
the 5 /
16
-18 x 3 /
4
bolt and lock nut (Ref 1). The nut should be on the inside of the hopper. The person in the
hopper can get out now.
2. Center the handle holder (Ref 9) between the bends on the brush guard (Ref B) with the handle holder
flush on the inside of the brush guard. Mark the two holes and drill through the brush guard with a 9 /
32
drill.
Use the two 1 /
4
- 20 x 1 1 /
2
bolts and lock nuts (Ref 8) to bolt handle holder to the brush guard. Cut and put
trim into the two notches that hold the hose handle.
3. Connect the hose to the hose handle (Ref 10) with the hose on the same side as the long handle. Then
put other end of hose to remote hose connector (Ref 4). Use the two hose clamps (Ref 6) to hold hose in
place.
4. Remove cover plate from in front of the vacuum housing and place in pocket on chute. Place the remote
hose connector into the pocket that the cover plate came out of. The cover plate and the remote hose
connector must be switched depending which operation you are doing.
5. For storage, loop the vacuum hose over the hose rack (Ref 2) and place the hose handle (Ref 10) into the
handle holder (Ref 9).
6. When you are going to operate the vacuum, pull handle stop (Ref 5) towards the front of machine and lift
up handle (Ref A). While holding handle (Ref A) up, push handle stop (Ref 5) back so that it holds the
handle (Ref A) up.
7. You may want to remove the hose handle, hose and remote hose connector if you are not going to use the
vacuum for an extended amount of time.