Smithco Supreme 35-000 (sn 101978) Parts & Service Manual - Manual (Page 85)

83
Accessories
13-438 RAKE ASSEMBLY WITH FINISHING BLADES PARTS LIST
REF# PART# DESCRIPTION QUANTITY
1 13-441 Right Rake 1
2 HMB-12-14 Machine Bushing 1 /
2
x 14GA 11
3 HMB-58-14 Machine Bushing 5 /
8
x 14GA 2
4 HNCL-58-11 Lock Nut 5 /
8
- 11 2
5 HP-18-100 Cotter Pin 1 /
8
x 1 3
6 13-440 Center Rake 1
7 13-443 Finishing Blade 5
8 13-439 Left Rake 1
9* 13-445 Rake teeth Kit (25 19-106 studs) 1
10 13-442 Groomer Blade 3
11 HCP-12-150 Clevis Pin 1 /
2
- 1 1 /
2
3
HHP-18 Bridge Pin 1 /
8
1
12 13-365 Drawbar 1
13 HB-58-11-400 Bolt 5 /
8
- 11 x 4 2
14 34-047 Rake Lift
15 34-019 Hitch Attachment 1
17 13-647 Hitch (includes Ref 20) 1
18 HCP-12-450 Clevis Pin 1 /
2
- 4 1 /
2
1
19 13-417 Connector Link 10
20 HSSQS-38-16-200 Stainless Steel Square Head Set Screw 3 /
8
-16 x 2 2
HNS-38-16 Stainless Steel Nut 3 /
8
- 16 2
* 19-106 Studs and Hardware used in Rake Teeth Kit 25
INSTALLATION INSTRUCTIONS
1. Attach drawbar (Ref 12) to hitch (Ref 17) using clevis pin (Ref 18), machine bushing (Ref 2) and cotter pin (Ref 5).
2. Bolt rake teeth (Ref 9) to frames, keeping all the same length. Leave the two outside holes on right and left rake open
(Ref A).
3. Lay out rake frames (Ref 1,6 and 8). Connect them using clevis pin (Ref 11), machine bushing (Ref 2) and cotter pin
(Ref 5).
4. Attach drawbar to left and right frames using bolt (Ref 13), machine bushing (Ref 3), and nut (Ref 4).
5. Attach five finishing blades (Ref 7) to the tabs of the rake frames using master link (Ref 19). Blades may be mounted
with saw tooth up or down, depending on the desired finish of the sand trap.
6. Attach rake hitch (Ref 17) to trap rake hitch on the rear axle using a clevis pin (Ref 11) and bridge pin.
7. The end links of chain on drawbar (Ref 12) are to be hooked to the hooks of the trap rake lift (Ref 14).
8. With the rake on the ground pull the rake to the right side until it is 2-3 inches from the tire.
9. Using the adjustment screw (Ref 20) on the right, adjust the screw until it hits the trap rake hitch, located on rear axle.
Lock jam nut so adjustment will not change.
10. Repeat steps 8 and 9 on left side.
11. Turn machine on and test for operation of rake assembly by raising and lowering the rake assembly. Also with rake
down, turn sharp corners to check that rake does not touch wheels.
12. NOTE: Test rake in sand to assure tire tracks are covered by the rake when turning sharp corners in either direction. If
there are tire tracks, readjust using the adjusting screws on the hitch, so the rake comes closer to the tire.
GROOMER BLADES - GOLF COURSE USE ONLY.
1. Place the three groomer blades (Ref 10) under the three rake assemblies (Ref 1, 6 and 8).
2. Center blades below rear most row of Rake teeth. The blade is designed to miss the outside two “teeth’ and fit around
the center ‘tooth’.
3. Remove the two ‘teeth’ that line up with slots of each groomer blade. Move blade up and into position and reattach
‘teeth’. Blade thickness should be accounted for by shortening the ‘teeth’ an equal length.