Smithco Supreme 35-000 (sn 101978) Parts & Service Manual - Manual (Page 67)

65
Accessories
34-168 SAND PLOW PARTS LIST
REF# PART# DESCRIPTION QUANTITY
1 34-018 Main Frame 1
2 34-192 Lift Handle 2
3 HB-12-13-200 Bolt 1 /
2
- 13 x 2 2
HNCL-12-13 Center Lock Nut 1 /
2
- 13 2
4 HMB-12-14 Machine Bushing 1 /
2
x 14GA 6
5 80-006 Rod End 2
6 HNJ-12-20 Jam Nut 1 /
2
- 20 2
7 15-015 Pedal Pad 1
8 16-062 Pedal Pad Plate 1
9 13-643 Left Lift Rod 1
10 HB-38-16-100 Bolt 3 /
8
- 16 x 1 2
HW-38 Washer 3 /
8
2
HWL-38 Lock Washer 3 /
8
2
HN-38-16 Nut 3 /
8
- 16 2
11 27-073 Right Lift Rod 1
12 27-017 Aluminum Sand Plow Blade 1
13-352 Steel Sand Plow Blade 1
13 HB-12-13-275 Bolt 1 /
2
- 13 x 2 3 /
4
2
HNCL-12-13 Center Lock Nut 1 /
2
-13 2
14 HB-38-16 -100 Bolt 3 /
8
- 16 x 1 4
HWL-38 Lock Washer 3 /
8
4
HN-38-16 Nut 3 /
8
- 16 4
15 13-167 Wear Blade 1
16 HB-38-16-300 Bolt 3 /
8
-16 x 3 2
HW-38 Washer 3 /
8
4
HNTL-38-16 Lock Nut 3 /
8
-16 2
17 13-169 Right Pusher Bar 1
18 HCP-12-150 Clevis Pin 2
HHP-18 Bridge Pin 1 /
8
2
19 13-168 Left Pusher Bar 1
20 HB-516-18-225 Bolt 5 /
16
- 18 x 2 1 /
4
2
HW-516 Washer 5 /
16
2
HNTL-516-18 Lock Nut 5 /
16
-18 2
21 34-193 Handle 1
22 34-016 Floorboard Support 1
23 15-019 Hand Grip 1
INSTALLATION INSTRUCTIONS
1. Disconnect the negative (-) ground battery cable from the battery.
2. Place the tabs on lift handle (Ref 2) over the bolts on the bottom of the bearing plate on the main frame with the angle
on the lift handle to the right side of the machine. Use two
3 /
8
lock nuts and flat washers. Tighten the two nuts at this
time.
3. Bolt handle (Ref 21 ) to lift handle using bolts, washers and lock nuts (Ref 20).
4. Put hand grip (Ref 23) onto the handle.
5. Assemble pusher bars (Ref 17 and 19) to plow (Ref 12) using hardware (Ref 10 and 13). There are two holes to bolt
hardware (Ref 10) in. Using hole closest to the blade will result in a shallow cut, whereas using the hole furthest from
the blade will result in a deeper cut. The slot on the pusher bar is for a more fine tuned adjustment.
6. Put pedal pad and pedal pad plate (Ref 7 and 8) into left lift rod (Ref 9) using hardware (Ref 10).
7. Put rod ends (Ref 5) onto lift rods with jam nuts (Ref 6) first. Adjust to equal lengths. Bolt lift rods (the one with the
pedal to the left side of the machine) to lift arms with the ball joints to the outside. Bolt from the outside with hardware
(Ref 3) with the
1 /
2
” machine bushing between rod end and lift arm.
8. Slide plow under machine and connect to machine as shown. Use clevis pin and cotter pin (Ref 18).
9. Connect lift rods to pusher bars using hardware (Ref 16) as shown. The three holes in the lift rods are for adjusting
the position of the hand lever. The Supreme can only use the bottom hole.