RGBLink VSP 3550S Quick Start User Manual
Page 2
VSP 3550 Quick Start
Rev 1.0
Page 2 of 4
Local Control
Front Panel Operation
Step 16-Power On
Connect with power cable, press the “POWER” and the
power indicator is turned on and after 10 seconds, the
monitor will be switched on and get into working status.
Step 13-USB interface
Used to connect the computer or console.
AC 85-264V 50/60Hz IEC-3 Power Interface .
Step 14-Sending Card interface
Sending card module port. Power has been already
supplied by video processor itself, no external power
supply needed for sending card.
Step 15-Power Interface and Switch
User Guideline
Inputs cable, outputs cable, control cable, power cable
were connected to interface finish turn on the power
switch, user guideline:
1. Set up OLED display language .
2. Set up output format.
3. Set up input source.
4. Save the above settings .
How to Do Customized Output Resolution
How to Scale the Layer Image
1. Push [MENU] button to enter the main menu, turn
knob and go to [OUTPUT FORMAT], push knob
and confirm to go into [CUSTOMIZED] menu.
2. Turn knob on each bit position, and change the value
of the bit by the digital buttons on the front panel.
3. After the digital push knob will add ×, means before
× is the horizontal size. Same operation for vertical
size.
4. After the digital push knob will add ×, means before
× is the vertical size. Same operation by push digital
buttons to set the refresh rate.
5. After input all the values, push knob to enable VSP
3550 to output this resolution. VSP 3550 will take
5~10 seconds to enable this output resolution.
How to Crop the Layer Image
1. Push any button of OUTPUT DVI1~DVI4, the
button blinks, and the layer can be edited.
2. Push [CROP] button, key lights, and start the crop
function.
3. Turn the knob, or push the number button to input
the number directly, push the knob to confirm.
4. Push [CROP] button again, key light is off, and exit
the crop function.
Address: S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone, Xiamen, Fujian Province, P.R.C
Tel: 00865925771197 Fax:00865925771202
Email: [email protected]
How to Realize Single Image Switching
1. Boot the system default CV1 to the current input
source (key flashes), if need seamless switching other
source such as DVI, direct light touch DVI key.
2. Choose DVI buttons, button lamp CV1 destroy, and
DVI key lights and flashes, can realize single image
of input signal source switching (input signal source
by original CV1 switching to DVI). The same method
can be switched CV2, VGA1, VGA2, DVI,HDMI,
SDI.
How to Set up the PIP
PIP: Push [MENU] button to enter the main menu,
choose [PIP] and select “ON” option.
LAYOUT: Can choose PIP layout.
SWAP IMAGE: It can set PIP to swap exchange, when
choose ON, it can realize IMAGE A and IMAGE B
exchange.
ALPHA: Can set the image display transparency,
regulating range between 0~16.
SELECT: Can choose to set the size or position of
IMAGE A or IMAGE B individually.
1. Push any button of OUTPUT DVI1~DVI4 and
LAYEY A and B, the button blinks, and the layer
can be edited.
2. Push [SCALE] button, key lights, and start the scale
function.
3. Turn the knob, or push the number button to input
the number directly, push the knob to confirm.
OLED shows as follows:
4. Push [SCALE] button again, key light is off, and
exit the scale function.
How to Set the Position of Layer Image
1. Push any button of OUTPUT DVI1~DVI4 and
LAYEY A and B, the button flashes, and the layer
can be edited.
2. Push [POS] button, key lights, and start the position
setting function.
3. Turn the knob, or push the number button to input
the number directly, push the knob to confirm.
4. Push [POS] button again, key light is off, and exit
the position setting function.
How to Achieve Split Function
1. Push button 4K×1K or any button in SPLIT part,
key lights, and enter the output split function.
2. VSP 3550 provides 9 kinds of split modes for user.
3. Turn the knob, user can select the split mode
according to actual need.