Metro Basix Plus Electronic Locking User Manual
Page 2
Section 8: User Codes·001
– 099
There are 99 User Code slots in addit
i
on to the 1 slot
reserved for the Super
v
isor Code
.
The User Code slots are
numbered 001 through 099
.
Enter User Codes:
Follow steps to enter Programming Mode (See
Section 5).
Enter 001.
Green Light Will Flash 4 Times.
Enter New 4 Digit User Code Combination (Valid
User code combinations are any number from 0001
to 9999).
Green Light Will Flash 1 Time followed by a slight
delay.
Green Light will then flash 3 times, prompting user
to enter next user code, programming location or to
exit
programming mode.
To program next User Code, enter 002 Green Light
will Flash 1 Time.
Enter Next New 4 Digit User Code Combination.
Green Light will flash 1 time followed by a slight
delay.
Green Light will then flash 3 times, prompting user
to enter next user code, programming location or to
exit programming mode.
Continue entering User Codes into the remaining
open slots by entering 003, 004, etc and following
the steps above.
Once finished entering the final User Code and
after the green light has flashed, you are free to
move on to additional programming features or to
hit 999 to exit programming mode (See Section 6).
Delete User Codes:
Follow steps to enter Programming Mode (Section
5).
Enter User Code location you wish to delete (001-
099).
Green Light Will Flash 4 Times.
Enter 0000 to delete user code.
Green Light Will Flash 1 Time followed by a slight
delay.
Green Light will then flash 3 times, prompting user
to delete next user code, enter next programming
location or to exit programming mode.
Continue deleting User Codes from the remaining
slots by entering 002, 003, etc and following the
steps above.
Once finished deleting user codes and after the
green light has flashed, you are free to move on to
additional programming features or to hit 999 to exit
programming mode (See Section 6 for more detail).
Section 9: Dual Mode Feature - 900
The electronic lock can be programmed to require both a
Supervisor code and a User code (dual mode) in order to
unlock and lock the car
t.
This will add an extra level of
security and control for the cart contents. The default is
dual mode deactivated
.
Activate Dual Mode:
Follow steps to enter Programming Mode (See
Section 5).
Enter 900.
Green Light Will Flash 1 Time.
Enter 1 To Enable Dual Mode.
Green Light Will Flash 1 Time followed by a slight
delay.
Green Light will then flash 3 times, prompting
user to enter next programming location or to exit
programming mode (See Section 6 for more
detail).
Disable Dual Mode:
Follow steps to enter Programming Mode (See
Section 5).
Enter 900.
Green Light Will Flash 1 Time.
Enter 0 to Disable Dual Mode.
Green Light Will Flash 1 Time followed by a slight
delay.
Green Light will then flash 3 times, prompting
user to enter next programming location or to exit
programming mode (See Section 6).
Section 10: Tamper Evident Lockout
– 901
If 5 incorrect codes are entered into the touch pad within
2 minutes, the tamper evident lockout feature will be
triggered and the cart will go into Access Denied mode.
Once tamper evident lockout is triggered, no user will be
able to access the cart for a set amount of time, even with
a valid code. The default Tamper Evident Lockout Time is
set to 5 minutes (300 seconds). The tamper evident
lockout out time is measured in seconds (i.e. 2 minutes =
120 seconds, 10 minutes = 600 seconds, etc.).
Change Tamper Evident Lockout Time
Follow steps to enter Programming Mode (See
Section 5).
Enter 901.
Green Light Will Flash 4 Times.
Enter 0001 - 9999 Seconds to program desired
amount of lockout time.
Green Light Will Flash 1 Time followed by a slight
delay.
Green
Light
will then flash 3 times
,
prompting
user
to enter
next
programming locat
i
on or
to
exit
programming mode
(See
Section
6
for
more
detail).
2