Measurement Computing 200 Series DaqBook - Manual (Page 41)

Daq Systems 02-13-02 DBK Basics, pg. 5
DBK Identification Tables
Analog Output DBKs
Analog Output
Product Name/Description I/O Conectivity
DBK2 Voltage Output Card 4 channels P1
DBK5 Current Output Card 4 channels P1
Digital I/O Control DBKs
Digital I/O / Control
Product Name/Description I/O Conectivity
DBK20 General-Purpose Digital I/O Card (Screw Terminals) 48 channels P2
DBK21 General-Purpose Digital I/O Card (DB37 Connectors) 48 channels P2
DBK23 Optically Isolated Digital-Input Module 24 channels P2
DBK24 Optically Isolated Digital-Output Module 24 channels P2
DBK25 Relay Output Card 8 channels P2
DBK208 Carrier board for Opto-22 Compatible Solid-State-Relay
Digital Modules.
Two 8-bit banks of
SSR modules Two P2s
P4
Analog Signal Conditioning DBKs
The DBKs that are used for analog signal conditioning attach to transducers and condition their outputs into
analog voltages. An A/D converter, located in the primary acquisition device, measures the analog
voltages. There are many signal-conditioning solutions available (and more are in development). Note that
DBK high-capacity modules require more circuitry than can fit on a compact card.
Analog Signal Conditioning
Product Name/Description I/O Connectivity
1
DBK4 Dynamic Signal Input Card 2 channels P1
DBK7 Frequency-to-Voltage Input Card 4 channels P1
DBK8 High-Voltage Input Card 8 channels P1
DBK9 RTD Measurement Card 8 channels P1
DBK12 Low-Gain Analog Multiplexing Card Note 2 16 channels P1
DBK13 High-Gain Analog Multiplexing Card Note 2 16 channels P1
DBK15 Universal Current/Voltage Input Card Note 2 16 channels P1
DBK16 Strain-Gage Measurement Card 2 channels P1
DBK17 Simultaneous Sample & Hold Card 4 channels P1
DBK18 Low-Pass Filter Card 4 channels P1
DBK19 Thermocouple Card Note 2 14 channels P1
DBK42 5B Isolated Signal-Conditioning Module 16 channels P1
DBK43A Strain-Gage Measurement Module 8 channels P1
DBK44 5B Isolated Signal-Conditioning Card 2 channels P1
DBK45 SSH and Low-Pass Filter Card 4 channels P1
DBK50 Isolated High-Voltage Input Module 8 channels P1
DBK51 Isolated Low-Voltage Input Module 8 channels P1
DBK52 Thermocouple Input Module Note 2 14 channels P1
DBK53 Low-Gain Analog Multiplexing Module Note 2 16 channels P1
DBK54 High-Gain Analog Multiplexing Module Note 2 16 channels P1
DBK70 Vehicle Network Interface, Analog Multiplexer Module 16 channels P1
DBK80 Differential Voltage Input Card with Excitation Output 16 channels P1
DBK81 Thermocouple Card, High-Accuracy 7 channels P1
DBK82 Thermocouple Card, High-Accuracy 14 channels P1
DBK83 Thermal Couple Card, High-Accuracy; uses Connection Pod 14 channels POD-1
DBK84 Thermocouple Module, High-Accuracy 14 channels P1
DBK207 Carrier Board for 5B Compatible Analog Input Modules 16 channels Two P1s / P4
DBK207/CJC Carrier Board for 5B Compatible Analog Input Modules.
DBK207/CJC includes cold junction compensation (CJC)
16 channels Two P1s / P4
Note 1: P1, P2, and P3 DB37 connectors do not exist on the DaqBoard/2000 Series or /2000c Series boards,
but are obtained by using P4 adapters (DBK200 series). These adapters typically connect to the
DaqBoard/2000 Series [/2000c Series] 100-pin P4 connector via a CA-195 cable.
Note 2: For DaqBoard/2000 and cPCI DaqBoard/2000 Series boards, internal clocks should be set to 100 kHz
when used with any of the following DBK options:
DBK12 , DBK13 , DBK15 , DBK19 , DBK52 , DBK53 ,
and DBK54 . See specific DBK section for details.