Marantz SR9600N - Manual (Page 33)

29
ENGLISH
RS232C
Connect an external control device or other device
for servicing. (Use a straight cable for the
connection.)
DC OUT (DC TRIGGER)
External devices can be controlled from the
SR9600 by connecting them to the DC OUT
terminal (12 V).
EMITTER OUT
Outputs the remote control signal input to the IR
RECEIVER IN terminals. External components
can be controlled by connecting them to the
EMITTER OUT terminal.
FLASHER IN
This receiver can be controlled by connecting a
control box or other control device to this receiver.
USB AUDIO
OUTPUT INPUT-1 (DVD)
INPUT-2 (DSS) INPUT-1 (DVD) INPUT-3 (VCR-1)
2
CD
INPUT-2 (DSS)
2
1 1
2
3
4 4
3
RS232C DC OUT EMITTER OUT MULTI RC RC-5
MONITOR OUT 1 OUT IN OUT IN DSS TV DVD LD
TAPE
VCR-1
OUTPUT-2
OUTPUT-1
IN
MAIN IN 7.1CH IN MULTI OUT
SURR. RIGHT
SURR. LEFT
SPEAKER SYSTEMS FRONT A OR B, CENTER, SURR,
SURR BACK : MINIMUM 6 OHMS
FRONT A + B : MINIMUM 8 OHMS
CENTER
FRONT B RIGHT
FRONT B LEFT
FRONT A RIGHT
FRONT A LEFT
SL SBL SL SR SBL SBR
SW
A B
SBR SR
COAX
OPT
8
7
6
2
5
4
3
1
DIGITAL IN
DIGITAL OUT
OUT
AC IN
CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR Y
CB/PB CR/PR Y
R
L
MODEL NO. SR9600
TUNER-1
FM(75 Ω ) GND AM
FM(75 Ω ) GND AM
TUNER-2
(AUDIO)
S400
S400
INPUT-4 (VCR-2 / DVD-R)
VCR-2 / DVD-R
IN CD-R / MD OUT
R
L
(AUX 2)
C
AUDIO
PRE OUT
L R C
AUDIO SW
VIDEO
S-VIDEO
R
L
MULTI OUT
VIDEO
A B
COMPONENT VIDEO
HDMI Ver 1.1
FLASHER RECEIVER IN IN
IR
OUT
IN
SURR.BACK /MULTI SPK. /SPK. C RIGHT
SURR.BACK /MULTI SPK. /SPK. C LEFT
ON
OFF SPEAKER C
UNSWITCHED 100W MAX
AC OUTLET 230V 50/60HZ
2
1 1
2
3
4 4
3
RS232C DC OUT EMITTER OUT
FLASHER RECEIVER IN IN
IR
2
1 1
2
3
4 4
3
RS232C DC OUT EMITTER OUT
FLASHER RECEIVER
IN IN
IR
CONNECTING OTHER EQUIPMENT
IR RECEIVER IN
This receiver can be operated by remote control
wit h out us ing t he int er nal I R r ec ei ve r, by
connecting an external IR receiver.
An IR receiver is connected as shown above.
Caution:
Wrongly connecting an IR receiver or connecting
an IR receiver of the wrong voltage can damage
the SR9600, therefore do not do this.
+12V
GND
Signal
ERROR MESSAGES FOR CONNECTED i.LINK
DEVICES
“LOOP CONNECT”
This message is displayed if the i.LINK device is
connected in a loop. Connect the device so that
the connection does not form a loop.
“NODE OVER”
This message is displayed if more than 63
i.LINK devices are connected to the SR9600,
including the SR9600. Limit connections to 63 a
maximum devices including the SR9600.
“HOP OVER”
This message is displayed if more than 17
i.LINK devices are connected in a daisy chain.
Keep daisy chain connections to a maximum 17
devices.
“BUS FULL”
This message is displayed if too many devices
are outputting signals on the i.LINK bus. Either
shut off power or disconnect unused devices.
“CANNOT LINK”
This message is displayed if the SR9600 cannot
connect to an i.LINK device or if an unconnected
d e v i c e i s s e l e c t e d a s t h e i n p u t s o u r c e .
Disconnect and reconnect the i.LINK cable, or
shut power to the SR9600 off and turn it back on.
M E S S A G E S W H E N A N i . L I N K D E V I C E I S
CONNECTED
“LINK CHECK”
This message is displayed while the SR9600
c h e c k s f o r c h a n g e s i n i . L I N K d e v i c e
connections.
“NO SIGNAL”
This message is displayed if a signal not
supported by the SR9600 is input.
SR9600N DFU_01_ENG 3_4 05.5.23, 5:47 PM Page 29 Adobe PageMaker 6.5J/PPC