Marantz SR9600N - Manual (Page 29)

25
ENGLISH
USB AUDIO
OUTPUT INPUT-1 (DVD)
INPUT-2 (DSS) INPUT-1 (DVD) INPUT-3 (VCR-1)
2
INPUT-2 (DSS)
2
1 1
2
3
4 4
3
RS232C DC OUT EMITTER OUT MULTI RC RC-5
1 OUT IN OUT IN
OUTPUT-2
OUTPUT-1 SURR. RIGHT
SURR. LEFT
SPEAKER SYSTEMS FRONT A OR B, CENTER, SURR,
SURR BACK : MINIMUM 6 OHMS
FRONT A + B : MINIMUM 8 OHMS
FRONT B RIGHT
COAX
OPT
8
7
6
5
DIGITAL OUT
AC IN
CB / PB CR / PR Y CB / PB CR / PR Y CB / PB CR / PR Y CB / PB CR / PR Y
CB / PB CR / PR Y
MODEL NO. SR9600
FM(75 Ω ) GND AM
FM(75 Ω ) GND AM
TUNER-2
INPUT-4 (VCR-2 / DVD-R)
VIDEO
S-VIDEO
MULTI OUT
VIDEO
A B
COMPONENT VIDEO
HDMI Ver 1.1
FLASHER RECEIVER IN IN
IR
OUT
IN
UNSWITCHED 100W MAX
AC OUTLET 230V 50/60H Z MULTI RC RC-5
OUT
IN
REMOTE
CONTROL
REMOTE
CONTROL
REMOTE
CONTROL
IN
OUT
IN
OUT
IN
OUT
EXTERNAL INTERNAL EXTERNAL INTERNAL EXTERNAL INTERNAL
1
RC OUT
2
USB AUDIO
OUTPUT INPUT-1 (DVD)
INPUT-2 (DSS) INPUT-1 (DVD) INPUT-3 (VCR-1)
2
CD
INPUT-2 (DSS)
2
1 1
2
3
4 4
3
RS232C DC OUT EMITTER OUT MULTI RC RC-5
MONITOR OUT 1 OUT IN OUT IN DSS TV DVD LD
TAPE
VCR-1
OUTPUT-2
OUTPUT-1
IN
MAIN IN 7.1CH IN MULTI OUT
SURR. RIGHT
SURR. LEFT
SPEAKER SYSTEMS FRONT A OR B, CENTER, SURR,
SURR BACK : MINIMUM 6 OHMS
FRONT A + B : MINIMUM 8 OHMS
CENTER
FRONT B RIGHT
FRONT B LEFT
FRONT A RIGHT
FRONT A LEFT
SL SBL SL SR SBL SBR
SW
A B
SBR SR
COAX
OPT
8
7
6
2
5
4
3
1
DIGITAL IN
DIGITAL OUT
OUT
AC IN
CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR Y CB/PB CR/PR Y
CB/PB CR/PR Y
R
L
MODEL NO. SR9600
TUNER-1
FM(75 Ω ) GND AM
FM(75 Ω ) GND AM
TUNER-2
(AUDIO)
S400
S400
INPUT-4 (VCR-2 / DVD-R)
VCR-2 / DVD-R
IN CD-R / MD OUT
R
L
(AUX 2)
C
AUDIO
PRE OUT
L R C
AUDIO SW
VIDEO
S-VIDEO
R
L
MULTI OUT
VIDEO
A B
COMPONENT VIDEO
HDMI Ver 1.1
FLASHER RECEIVER IN IN
IR
OUT
IN
SURR.BACK /MULTI SPK. /SPK. C RIGHT
SURR.BACK /MULTI SPK. /SPK. C LEFT
ON
OFF SPEAKER C
UNSWITCHED 100W MAX
AC OUTLET 230V 50/60HZ
7.1CH IN SL SBL
SW SBR SR R
L
(AUX 2)
C
PRE OUT
MAIN IN SL SR SBL SBR L R C
SW
L
R
FRONT SURR. SURR.
BACK
SUB
WOOFER
CENTER
L
R
FRONT SURR. SURR.
BACK
SUB
WOOFER
CENTER
L R L R L R L R L R L R
R L R L R L R L R L R L
ADVANCED CONNECTION
CONNECTING MULTICHANNEL AUDIO SOURCE
The 7.1ch input jacks are for multichannel audio
source such as a Super Audio CD multichannel
player, DVD-audio player or external decoder.
If you use these jacks, switch on the 7.1ch input
and set the 7.1ch input level from the OSD menu
system. (see page 33).
CONNECTING AN EXTERNAL POWER AMPLIFIER
The PRE OUT jacks are for connecting external
power amplifiers.
Be sure to connect each speaker to the corresponding
external power amplifier.
POWER
AMPLIFIER
DVD-AUDIO PLAYER
or
SUPER AUDIO CD
MULTICHANNEL PLAYER
Center Front
Left Front
Right
Surround
Left Surround
Right
Subwoofer
Surround Back Left
CONNECTING THE REMOTE CONTROL JACKS
MD DECK CD RECORDER
q
You can control other Marantz products through
the SR9600 with the remote control by connecting
the REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote control is
received by the remote sensor on the SR9600,
then the signal is sent to the connected device
through this terminal. Therefore you need to aim
the remote control only at the SR9600. Also, if a
Marantz power amplifier (some models excluded)
is connected to one of these terminals, the power
amplifier’s power switch is synchronized with this
unit’s power switch.
Set the REMOTE CONTROL SWITCH on the other
units, (not the SR9600) to “EXT.”(external) to use
this feature.
CD PLAYER
IR RECEIVER
w
Whenever external infrared sensors or similar
devices are connected to the RC-5 IN jack on the
SR9600, be sure to always disable operation of the
infrared sensor on the SR9600 by using the
following procedure.
1. Hold down the MULTI button and the MENU
button on the front panel at the same time for
five seconds.
2. The setting “IR=ENABLE” is shown on the FL
display.
3. Press the ENTER buttons to change this to
“IR=DISABLE”.
4. Press the OK/ENTER button for five seconds.
The infrared sensor on the main unit is now
disabled.
Note:
• Be sure to set to “IR=ENABLE” when external
infrared sensors or similar devices are not
connected. Otherwise, the SR9600 will be unable
to receive remote control commands.
5. To restore to the original setting, perform
steps 1 to 4 and set to “IR=ENABLE”.
Surround Back Right
SR9600N DFU_01_ENG 3_4 05.5.23, 5:47 PM Page 25 Adobe PageMaker 6.5J/PPC