Specifications, Resetting the microprocessor – Marantz NR1601 User Manual
Page 81
75
Basic version
Advanced version
Simple version
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
NEDERLANDS
SVENSKA
Information
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
NEDERLANDS
SVENSKA
Resetting the microprocessor
Perform this procedure if the display is abnormal or if operations cannot be performed.
When the microprocessor is reset, all the settings are reset to their default values.
Various setting details can be saved and reset on this device. If setting details are saved before returning
to the default values, after returning to the default settings, setting details can be returned to the same
values as before returning to the defaults.
To return all of the settings to the default values, perform steps 2 to 4 without performing step 1.
RETURN
ENTER STATUS
ON/STANDBY
MENU
1
When the power is ON, press and hold
STATUS
and
ENTER
for more than 3 seconds.
After “MEMORY SAVING” is shown on the display, “COMPLETE”is shown to inform you that the
settings have been saved.
2
Turn off the power using
ON/STANDBY
.
3
Press
ON/STANDBY
while simultaneously pressing
ENTER
and
RETURN
.
4
Once the display starts flashing at intervals of about 1 second, release the two
buttons.
5
Press and hold
STATUS
and
MENU
for more than 3 seconds.
After “MEMORY LOAD” is shown on the display, “COMPLETE” is shown to inform you that the
settings have returned to those saved in step 1.
If in step 4 the display does not flash at intervals of about 1 second, start over from step 2.
Specifications
n
Audio section
• Power amplifier
Rated output:
Front:
50 W + 50 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.)
75 W + 75 W (6 Ω, 1 kHz with 10 % T.H.D.)
Center:
50 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.)
75 W (6 Ω, 1 kHz with 10 % T.H.D.)
Surround:
50 W + 50 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.)
75 W + 75 W (6 Ω, 1 kHz with 10 % T.H.D.)
Surround Back:
50 W + 50 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.)
75 W + 75 W (6 Ω, 1 kHz with 10 % T.H.D.)
Output connectors:
6 – 8 Ω
• Analog
Input sensitivity/Input impedance:
130 mV/50 kΩ
Frequency response:
10 Hz – 100 kHz — ±3 dB (Source Direct mode)
S/N:
98 dB (IHF–A weighted, Source Direct mode)
n
Video section
• Standard video connectors
Input/output level and impedance:
1 Vp-p, 75 Ω
Frequency response:
5 Hz – 10 MHz — +1, –3 dB
• Color component video connector
Input/output level and impedance:
Y (brightness) signal — 1 Vp-p, 75 Ω
P
B
/ C
B
signal — 0.7 Vp-p, 75 Ω
P
R
/ C
R
signal — 0.7 Vp-p, 75 Ω
Frequency response:
5 Hz – 60 MHz — +0, –3 dB
n
Tuner section
[FM]
[AM]
(Note: μV at 75 Ω, 0 dBf = 1 x 10
–15
W)
Receiving Range:
87.5 MHz – 108.0 MHz
522 kHz – 1611 kHz
Usable Sensitivity:
1.2 μV (12.8 dBf)
18 μV
50 dB Quieting Sensitivity:
MONO 2.0 μV (17.3 dBf)
STEREO 42 μV (34.5 dBf)
S/N (IHF-A):
MONO 70 dB
STEREO 67 dB
Total harmonic Distortion (at 1 kHz):
MONO 0.3 %
STEREO 0.7 %
n
General
Power supply:
AC 230 V, 50 Hz
Power consumption:
250 W
0.2 W (Standby)
3 W (CEC standby)
Maximum external dimensions:
440 (W) x 105 (H) x 367 (D) mm
Weight:
9.0 kg
n
Remote control unit (RC010SR)
Batteries:
R03/AAA Type (two batteries)
For purposes of improvement, specifications and design are subject to change without notice.