Hypertherm Powermax30 Service Manual - Manual (Page 6)

WARRANTY
Hypertherm Plasma Systems iii
8-06
Warning
Genuine Hypertherm parts are the factory-
recommended replacement parts for your Hypertherm
system. Any damage caused by the use of other than
genuine Hypertherm parts may not be covered by the
Hypertherm warranty.
Warning
You are responsible for the safe use of the Product.
Hypertherm does not and cannot make any guarantee
or warranty regarding the safe use of the Product in
your environment.
General
Hypertherm, Inc. warrants that its Products shall be free
from defects in materials and workmanship, if
Hypertherm is notified of a defect (i) with respect to the
power supply within a period of two (2) years from the
date of its delivery to you, with the exception of
Powermax Series power supplies, which shall be within
a period of three (3) years from the date of delivery to
you, and (ii) with respect to the torch and leads within a
period of one (1) year from its date of delivery to you.
This warranty shall not apply to any Product which has
been incorrectly installed, modified, or otherwise
damaged. Hypertherm, at its sole option, shall repair,
replace, or adjust, free of charge, any defective Products
covered by this warranty which shall be returned with
Hypertherm’s prior authorization (which shall not be
unreasonably withheld), properly packed, to
Hypertherm’s place of business in Hanover, New
Hampshire, or to an authorized Hypertherm repair
facility, all costs, insurance and freight prepaid.
Hypertherm shall not be liable for any repairs,
replacement, or adjustments of Products covered by this
warranty, except those made pursuant to this paragraph
or with Hypertherm’s prior written consent. The warranty
above is exclusive and is in lieu of all other
warranties, express, implied, statutory, or otherwise
with respect to the Products or as to the results
which may be obtained therefrom, and all implied
warranties or conditions of quality or of
merchantability or fitness for a particular purpose or
against infringement. The foregoing shall constitute
the sole and exclusive remedy for any breach by
Hypertherm of its warranty. Distributors/OEMs may
offer different or additional warranties, but Distributors/
OEMs are not authorized to give any additional warranty
protection to you or make any representation to you
purporting to be binding upon Hypertherm.
Certification test marks
Certified products are identified by one or more
certification test marks from accredited testing
laboratories. The certification test marks are located
on or near the data plate. Each certification test mark
means that the product and its safety-critical
components conform to the relevant national safety
standards as reviewed by that testing laboratory.
Hypertherm places a certification test mark on its
products only after that product is manufactured with
safety-critical components that have been authorized
by the accredited testing laboratory.
Once the product has left the Hypertherm factory, the
certification test marks are invalidated if any of the
following occurs:
• The product is significantly modified in a manner that
creates a hazard or non-conformance.
• Safety-critical components are replaced with
unauthorized spare parts.
• Any unauthorized assembly or accessory that uses or
generates a hazardous voltage is added.
• There is any tampering with a safety circuit or other
feature that is designed into the product as part of the
certification.
CE marking constitutes a manufacturer’s declaration of
conformity to applicable European directives and
standards. Only those versions of Hypertherm products
with a CE Marking located on or near the data plate
have been tested for compliance with the European Low
Voltage Directive and the European EMC Directive.
EMC filters needed to comply with the European EMC
Directive are incorporated within versions of the power
supply with a CE Marking.
Patent indemnity
Except only in cases of products not manufactured by
Hypertherm or manufactured by a person other than
Hypertherm not in strict conformity with Hypertherm’s
specifications and in cases of designs, processes,
formulae, or combinations not developed or purported to
be developed by Hypertherm, Hypertherm will defend or
settle, at its own expense, any suit or proceeding
brought against you alleging that the use of the
Hypertherm product, alone and not in combination with
any other product not supplied by Hypertherm, infringes
any patent of any third party. You shall notify Hypertherm
promptly upon learning of any action or threatened