Hypertherm Shape Cutting Control User Manual
Page 27
MicroEdge
21
Mating Connector
Terminal Connections
Control & Cable Pinout for Sensor THC
I/O Configuration Type “P”
Note: A 9C Amp connector is provided on the back of the control (I/O Type “P”)
for interfacing.
Control 9C Divider J2
Analog Pin #
Description
Pin #
1
24V
Common
1
2
Nozzle
Contact
Sense
+ 2
3
Nozzle
Contact
Sense
– 3
4
Nozzle
Contact
Enable
+
4
5
Nozzle
Contact
Enable
–
5
6
Analog
+
6
7
Analog
–
7
8
Hold
Ignition
+
N/A
(direct
to
power
supply)*
9
Hold
Ignition
–
N/A
(direct
to
power
supply)*
Ground
Stud
Shield
No
Connection
Analog Mating Connector
Connector AMP # 206708-1
Backshell AMP #206966-1
Sockets #66105-3 (20-24 ga)
VDC Mating Connector
8C Phoenix Connector – Phoenix Part # 1803633
Cable
Belden #9505 or equivalent
* Note: It is recommended that the Hold Ignition input be wired to the Power
Supply through an external relay for noise immunity. Please refer to Instructions
from the supply manufacturer for details on connection to the Hold Ignition Input.
- EDGE Pro Ti Shape Cutting Control Rev.2 (288 pages)
- 80669J Rev.3 (304 pages)
- HD3070 Plasma Arc Cutting System w/ Manual Gas Console (281 pages)
- MAXPRO200 Rev.2 (294 pages)
- MicroEDGE Pro Shape Cutting Control Rev.2 (182 pages)
- HPR260 Auto Gas Preventive Maintenance Program Rev.4 (288 pages)
- Powermax1650 (317 pages)
- PHC Sensor (58 pages)
- HTA Rev 6.00 Operators Manual (212 pages)
- HTA Rev 7.00 Install Guide (242 pages)
- THC Control Board Replacement (13 pages)
- THC Plasma Interfacer Upgrade (9 pages)
- THC X-Y Table Product Configuration (20 pages)
- D845GERG2 (128 pages)
- MRT2 (64 pages)
- MRT (98 pages)
- Duramax Hyamp Long Handheld Torches (92 pages)
- Duramax Hyamp Robotic Torch (74 pages)
- HyIntensity Fiber Laser Rev.3 (240 pages)
- PCBS-0124 (70 pages)
- SuperMicro 370SBA 533Mhz (90 pages)
- LR2075 (56 pages)
- Phoenix 8.0 (585 pages)
- LH2125 (60 pages)
- HD3070 w/ Automatic Gas (35 pages)
- HD3070 w/Manual Gas (43 pages)
- HD4070 Rev.8 (278 pages)
- HD4070 Product Configuration (88 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (32 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (33 pages)
- HPR800XD Manual Gas Rev.2 (368 pages)
- HPRXD Short Torch with Integrated Lead Rev.1 (30 pages)
- HT4001 (59 pages)
- DuraChill 5 HP Air-Cooled Chiller For Hypertherm (29 pages)
- HT4001 Air Injected Water Muffler System (40 pages)
- H601 Power Supplies (62 pages)
- MAX200 Remote Switch (9 pages)
- HT4100 Plasma Arc Cutting System Operating (50 pages)
- HT4001 Plasma Arc Cutting System (259 pages)
- HSD130 HySpeed Plasma (233 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.7 (53 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.27 (289 pages)
- MAX200 Water Muffler (39 pages)
- HT2000LHF Product Configuration (23 pages)