Hypertherm Shape Cutting Control User Manual
Page 25
MicroEdge
19
8
Output 4 +
Hold Ignition ( Relay Contact )
9
Output 4 –
Hold Ignition ( Relay Contact )
Ground
Stud
Shield
Mating Connector
Connector AMP #206708-1
Backshell AMP #206966-1
Sockets (20-24 ga) AMP #66105-3
Cabling: Use Belden # 9504 or equivalent
Joystick
Pin # Designation
Description
1
Input
1
Joystick
UP
2
Input
2
Joystick
DWN
3
Input
3
Joystick
LT
4
Input
4
Joystick
RT
5
Common
Common
6
Analog Input 3 +
Speed Pot 1
7
Analog Input 3 –
Speed Pot 1
8
Analog Input 4 +
Speed Pot 2
9
Analog Input 4 –
Speed Pot 2
Ground
Stud
Shield
Note: Joystick inputs are activated by passing the Common signal ( pin 5 ) to the
desired input.
Analog inputs for the speedpots are rated at 0 - +10VDC
Mating Connector
Connector AMP #206708-1
Backshell AMP #206966-1
Sockets (20-24 ga) AMP #66105-3
Cabling: Use Belden # 9504 or equivalent
THC and Joystick Cable Grounding
Cable shields should be tied to the external PE studs for optimum noise
immunity.
- EDGE Pro Ti Shape Cutting Control Rev.2 (288 pages)
- 80669J Rev.3 (304 pages)
- HD3070 Plasma Arc Cutting System w/ Manual Gas Console (281 pages)
- MAXPRO200 Rev.2 (294 pages)
- MicroEDGE Pro Shape Cutting Control Rev.2 (182 pages)
- HPR260 Auto Gas Preventive Maintenance Program Rev.4 (288 pages)
- Powermax1650 (317 pages)
- PHC Sensor (58 pages)
- HTA Rev 6.00 Operators Manual (212 pages)
- HTA Rev 7.00 Install Guide (242 pages)
- THC Control Board Replacement (13 pages)
- THC Plasma Interfacer Upgrade (9 pages)
- THC X-Y Table Product Configuration (20 pages)
- D845GERG2 (128 pages)
- MRT2 (64 pages)
- MRT (98 pages)
- Duramax Hyamp Long Handheld Torches (92 pages)
- Duramax Hyamp Robotic Torch (74 pages)
- HyIntensity Fiber Laser Rev.3 (240 pages)
- PCBS-0124 (70 pages)
- SuperMicro 370SBA 533Mhz (90 pages)
- LR2075 (56 pages)
- Phoenix 8.0 (585 pages)
- LH2125 (60 pages)
- HD3070 w/ Automatic Gas (35 pages)
- HD3070 w/Manual Gas (43 pages)
- HD4070 Rev.8 (278 pages)
- HD4070 Product Configuration (88 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (32 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (33 pages)
- HPR800XD Manual Gas Rev.2 (368 pages)
- HPRXD Short Torch with Integrated Lead Rev.1 (30 pages)
- HT4001 (59 pages)
- DuraChill 5 HP Air-Cooled Chiller For Hypertherm (29 pages)
- HT4001 Air Injected Water Muffler System (40 pages)
- H601 Power Supplies (62 pages)
- MAX200 Remote Switch (9 pages)
- HT4100 Plasma Arc Cutting System Operating (50 pages)
- HT4001 Plasma Arc Cutting System (259 pages)
- HSD130 HySpeed Plasma (233 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.7 (53 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.27 (289 pages)
- MAX200 Water Muffler (39 pages)
- HT2000LHF Product Configuration (23 pages)