Bolt bag for: the standard az-el mount – DH Satellite 60 Fixed Az-El Mount User Manual
Page 20
BOLT BAG FOR: THE STANDARD AZ-EL MOUNT
C24F SEAVEY C & KU
FEED ASSEMBLY
AND STRUTS
1- Set of 4 Strut
s
1-
Colla
r
(C, Ku
)
1
2 -
5/16” Lock Washers & Nuts
attached to S
t
ruts
4- 2'
x
2
'
Angle Bracket
s
4- 5/16” x 1 ½” Bolts
8- 5/16” x 2 ¼” Bolts
C14F
C
HAP
A
RRAL
FEED
ASS
E
M
BLY
1- Set of 4 Struts
1- C
o
llar (C, Ku)
8- 1 ½” x 1/4” Bolts
8- ¼” Lock Washers & Nuts
EL
EVA
TION BRACKET
1- 5/16” x 2” U-Bol
t
2- 5/16” Lock Washers & Nuts
2- 5/8” Nuts
1- 5/8” Eyebolt
1- 1 ½” x 1 ½” Bolt
1- 1/2”
Nut
1- 3" x 2
"
x 2" El
ev
. Angle
1- 1/2” Lock Washers
RING TO DISH
12 TAB/ 6” RING
12- 1/2” x 1 ½” Bolts
1
2- 1/2” Nuts
12- 1/2” Lock Washers
24-
1/2” Rubber Washers
12-
1/2” Stee
l Was
her
s
MOUNT TO RING
2- 3/4” x 5” Bolts
2- 3/4” x 3” Bolts
4- 3/4” Nuts
2- 3/4” Steel Washers
4- 3/4” Lock Washers
Ku4FL: 3PC
ADD TO C14F
3- Section to 3pc collar
3 8-32 x 1” Bolts
3PC COLLAR TO HORSESHOE
3 8-32 x ¾” Bolts
3- #8 Fender Washers
3 8-32 Nuts
RING TO DISH
16 BLOCK/ 4” RING
16- ½” x 3” Bolts
16- ½” Flat Washers
32- ½” Rubber Washers
16- ½” Lock Washers
16- ½” Nuts
Template Rib Hardware: Sectional
Antenna Size
¼” x ¾” Bolts
¼” Lock Washers
¼” Nuts
3.0M
44
44
44
3.7M
52
52
52
3.8M
56
56
56
4.2M
120
120
120
4.5M
136
136
136
Splice Straps: Sectional
Antenna Size
Splice Straps
¼” x ¾” Bolts
¼” Lock Washers
¼” Nuts
3.0M
4
8
8
8
3.7M
4
8
8
8
3.8M
4
8
8
8
4.2M
8
16
16
16
4.5M
8
16
16
16
You will have 12 beveled washers for
the 3m antenna. See placement in
drawing above.
NOTE: SECTIONAL ANTENNAS INCLUDE ADDITIONAL
HARWARE, SEE TABLES BELOW
Page 15
Back Ring (1/4” x 6” x 60” dia)
Ring Tab (1 of 12)
½” nut
Beveled Washer
Rubber Washers
Antenna
½” x 1 ½” Bolt
½” Steel Washer
IMPORTANT: FOR 36” f/l Antennas Only
5/8” Hole
Base can with set screws.
RING TO DISH
16 TAB/ 6” RING
16- ½” x 1 ½” Bolts
16- ½” Flat Washers
32- ½” Rubber Washers
16- ½” Lock Washers
16- ½” Nuts
BACK BRACES
FOR 3.7m-4.2m
8- Back Braces
8- Brace Clips
8- Bent Tabs
24- ½” Nuts
8- ½” Lock Washers
8- 3/8” x 1 ½” Bolts
8- 3/8” Nuts
8- 3/8” Lock Washers
16- ¼” x ¾” Bolts
16- ¼” Nuts
16- ¼” Lock Washers
NOTE:
Stainless steel or DURA-CON® hardware provided.
*DURA-CON® is a corrosion resistant coating.
DURA-CON®: Problem of thread-galling is eliminated.
Beveled Washer
1 ½” x 1 ½”