Campomatic DW924BI - Manual (Page 7)

Th e wat er soften er must be s et m an u ally, usin g th e wa ter ha rd ness dia l.
Th e wat er soften er is des ign ed to remove min era ls an d sa lts from t he water, wh ich woul d h a ve
a de trim enta l o r advers e effe ct on the op e ration of the app liance.
Th e higher the conte nt o f the se mine rals and salts , th e h ar der yo ur wat er is .
Th e so ft ene r sho uld be a djus ted acco rd in g to the ha rd ness of t he wa te r in you r area. Yo ur lo cal Water Author ity
can ad vise y ou o n th e ha rdne ss o f th e water in y our ar ea .
Adjusting Salt Consumption
Th e dishwas her is desig ned to allow for a djus tment in the amo unt of sa lt co nsumed bas ed o n the ha rdne ss o f
the wate r us ed. This is in ten d ed to op timise and cus to mise th e level o f sa lt co n sum ptio n.
WATER SOFTENER
The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will
form on the dishes and utensils.
The appliance is equipped with a special softener that uses a salt container specifically designed to eliminate
lime and minerals from the water.
Contact your local water board for information on the hardness of your water su pply.
If your model does not have any water softener, you may skip this section.
Clark: British degree
fH: French degree
DH: German degree
dH=1.25 Clarke=1.78 fH =0.178 mmol/l 1
The manufa cto ry setting : H4 (EN 50242)
Be fore u sing you r dishwashe r for th e first time :
A. Set the wate r sof tene r
B. Add 1.5Kg d ishw ash er sa lt an d th en full fill the salt con ta in er with w ater
C. Fill t he rinse aid dis p enser
D. Fill i n d e terg ent
Ple a se follo w th e ste ps b elo w fo r adju stm en t in sa lt co nsu mpt ion.
1. Swit ch o n the a pplia nce;
2. Press the Start/Pause bu tton fo r more than
seconds to st art the water
softener set mode l within 6 0sec onds after th e a ppliance was
switched on;
3. Press the
to select the prope r set a ccording to
your lo cal e nv ironmen t, the sets will ch ange in the following
sequen ce : H1 ->H2->H3 ->H4->H5->H6;
4. Press the
to end the set up model.
5
bu tton
On/Off but to n or no operation for 5 second s
Start/Pause
dH mmol/l
0~9 0~5 0~0.94 0 /
10-20 6 -11 1.0-2.0 20 60
21-30 12-17 2.1-3.0 30 50
40 40
fH
0~6
7-14
15-21
Clarke
WATER HARDNESS
Selector Position
Salt consumption
(gram/cycle)
Auto nomy
(cycles/1kgs)
18- 22 31- 40 22-28 3.1-4.0
41-60 23-34 4.1-6.0 50 30
60 20
29-42
35- 55 61- 98 43- 69 6.1- 9.8
H1--Rapid Light bright
H2- - Light bright 1Hour
H3--1Hour Rapid Light bright 、
H4- - Light brig ht Gl ass
H5- -Gl ass Rapid Light br igh t 、
H6--Glass 1Hour Light bright 、