Denon DBP 4010UDCI - Manual (Page 10)

ENGLISH
Troubl
eshooting
Information
HDMI
Control
Function
Pl
ayback
Setup
Connections
Specifications
Inserting the Batteries
About the Remote Control Unit
e · Put·the·rear·cover·back·on.
q · Remove· the· remote· control·
unit’s·rear·cover.
w · Set· three· R6/AA· batteries· in·
the·battery·compartment·in·the·
indicated·direction.
NOTE
Use·R6/AA·batteries·in·this·remote·control.·
Replace· the· batteries· with· new· ones· if· the· set· does· not· operate·
even· when· the· remote· control· unit· is· operated· close· to· the· unit.·
(The·supplied·batteries·are·only·for·verifying·operation.)
When·inserting·the·batteries,·be·sure·to·do·so·in·the·proper·direction,·
following·the·“q”·and·“w”·marks·in·the·battery·compartment.
To prevent damage or leakage of battery fluid:
Do·not·use·a·new·battery·together·with·an·old·one.
Do·not·use·two·different·types·of·batteries.
Do·not·attempt·to·charge·dry·batteries.
Do·not·short-circuit,·disassemble,·heat·or·dispose·of·batteries·in·
flames.
If the battery fluid should leak, carefully wipe the fluid off the inside
of·the·battery·compartment·and·insert·new·batteries.
Remove·the·batteries·from·the·remote·control·unit·if·it·will·not·be·in·
use·for·long·periods.
Used·batteries·should·be·disposed·of·in·accordance·with·the·local·
regulations·regarding·battery·disposal.·
•
•
•
•
•
•
•
Operating Range of the Remote Control
Unit
Point·the·remote·control·unit·at·the·remote·sensor·when·operating·
it.
30°
30°
Approx.23feet/7m
NOTE
The·set·may·function·improperly·or·the·remote·control·unit·may·not·
operate· if· the· remote· control· sensor· is· exposed· to· direct· sunlight,·
strong artificial light from an inverter type fluorescent lamp or infrared
light.
Remote Control Settings (Remote
Control Side)
Switches when the DBP-4010UDCI’s remote control operates
another DENON BD players in the vicinity.
Set·the·remote·control·code·simultaneously·on·the·main·unit,·too.·
For· how· to· set· codes,· see· GUI· menu:· “Other· Setup”· –· “Remote·
Control·Setting”·–·“Remote·ID”·(vpage·31).
G Remote control code settingH
1 :·Set·the·remote·control·code·to·“1”.
2 :·Set·the·remote·control·code·to·“2”.
If·the·signal·code·of·the·remote·control·does·not·match·the·signal·
code·of·the·unit,·the·remote·control·code·set·on·the·unit·is·shown·
on·the·display.·
G
ExampleH
If·the·code·setting·on·the·unit·is·“DENON·1”,·and·the·setting·on·the·
remote·control·is·“2”,·“PLAYER·1”·is·shown·on·the·display.·
NOTE
Match·the·signal·code·of·the·remote·control·with·the·signal·code·of·
the·unit.·If·the·remote·control·code·is·different,·you·cannot·operate·
the·DBP-4010UDCI·with·the·remote·control.·
Even·if·you·change·the·remote·control·code,·set·GUI·menu·“Other·
Setup”· –· “Remote· Control· setting”· –· “Receive· Legacy· Remocon”·
(vpage· 31)· to· “Off”· when· operating· the· DBP-4010UDCI· with· a·
remote·control·other·than·DENON’s.
•
•
•
Getting Started