DVDO VP50 - Manual (Page 18)

27 28
LED Brightness
This selection allows the user to configure the behavior of the Front Panel LED brightness. The
‘normal’ parameter adjusts the brightness of the front panel led when the menu is being navigated.
The ‘navigate’ parameter adjusts the brightness of the front panel led during normal usage, when
the menu is not being navigated.
User Mode
You have limited access to the output timing controls in ‘Normal’ mode. In ‘Advanced’
user mode, you have access to the complete set of output timing controls. push the
q button to see the current setting and the fpd displays either ‘normal’ or ‘advanced’ user level.
push the q button again to select the alternate mode. The default setting is ‘normal’.
Serial Port Rate
The serial port is used by the automation system controllers to control the iscan Vp50 pro . The serial
port baud rate defaults to 9200 bps, but can be changed using the p or q button.
The supported baud rates are:
• 4800 bps (4.8K)
• 9600 bps (9.6K)
• 14400 bps (14.4K)
• 19200 bps (19.2K)
• 38400 bps (38.4K)
• 57600 bps (57.6K)
Factory Default
The factory default option allows you to reset all system settings to their factory defaults.
- press either the p or q button. The fpd displays ‘no’.
2- Press the same button to switch to ‘Yes’.
3- Confirm this selection by pressing the Enter button.
NOTE: resetting the iscan Vp50 pro to the factory defaults will cause all previously saved settings to
be lost. record any important settings before performing this action.
Software Update
use this parameter to install the latest software into your iscan Vp50 pro . The latest software is
available at www.anchorbaytech.com/update. The website includes complete download install
instructions.
12V Trigger Level
The state on the 2V triggers can be changed so that the connected device is in the correct state
when triggered by the iscan Vp50
pro .
Information
This setting shows information about the system including:
• Video source
• signal Type
• audio source
• aspect ratio
Output Status
• resolution
• frame rate
• line rate
• aspect ratio
This screen is helpful during troubleshooting.
Output Setup
Analog/Digital Output
The iscan Vp50 pro can output either an analog or digital video signal. The default setting is for the
digital, HdMi, output to be active. To output to a display with an analog input, insure that this setting
is set to ‘Analog (BNC)’
Output Format
The current selected output format will be highlighted in the osd in red. To select a different out-
put format, highlight it first and then press the
u button. adjustment of advanced timing controls
can also be made here although most displays do not need ‘custom’ timing. The user Mode, in the
Configuration menu, must be changed to ‘Advanced’ for the advanced timing controls to be acces-
sible. for a complete list of the available output presets, see the Complete Menu Tree in section 5.
Output Aspect Ratio Control
There are five controls for Output Aspect Ratio (OAR):
• display aspect ratio
• lens Mode
• screen aspect ratio
• image shift
• underscan
The Display Aspect Ratio is the full aspect ratio of the display, normally specified in the display manual.
The most common display aspect ratios are 4:3 and 6:9. less common ones are 5:4, 2.35: and
others. The example below shows a 4:3 projector with a 16:9 screen.
In this example, the region outside the Active Output area (called the mask) is inactive, and only impor-
tant for creating video timing signals for the display. input video data is never mapped to this region.
Mask
Active Output
Area
16
9
Mask
Screen Aspect Ratio
(2.35:1)
Screen Aspect Ratio
(2.35:1)
Visible Area Active
Output
Page 37, R2
page 38
Image
4
3