WaterFurnace Envision2 - Manual (Page 36)

36
ENVISION 2 COMPACT INSTALLATION MANUAL
1. Leaving Air Temperature (LAT) Sensor – This 10 kOhm
NTC sensor is factory installed on all UPC equipped
heat pumps. It typically is attached to wiring inside
the blower cabinet on the suction side of the blower.
This sensor is attached on ABC FP2 pins available as
LAT AU-30.
1. Compressor Proving Sensors – This optional factory
installed current sensor is connected to confirm
compressor operation via the power wires. The sensor
is attached at ABC Y1 and available at point BV-65.
1. Valve End Switch – This optional input is setup for a field
installed flow valve end switch. This end switch input is
attached at ABC Y2 and available at point BV-67.
1. Fan Proving Sensors – This optional factory installed
current sensor is connected to confirm fan operation
via the power wires. The sensor is attached at ABC G
and available at point BV-33.
1. Occupancy Sensor - This standard feature includes a
field installed and wired room sensor with occupancy
sensor typically found in DDC systems. The RNet
room sensors can be found thru your commercial
representative. The occupancy Sensors are attached at
ABC 0 and can be found at point BV-49.
1. Dirty Filter Switch – This optional field installed switch
is connected to confirm dirty filter operation. The
dirty filter switch can be found thru your commercial
representative. The sensor is attached at ABC W and
available at point BV-63.
2. Fault, Configuration, and Status Codes – The codes
can be visible to the BAS if desired
Fault LED (LED1, Red)
Red Fault LED
LED Flash
Code *
Lockout
Reset/
Remove
Fault Condition Summary
ABC Basic F
aults
Normal - No Faults Off -
Fault-Input 1 No Auto Tstat input error. Autoreset upon condition removal.
Fault-High Pressure 2 Yes Hard or Soft HP switch has tripped (>600 psi)
Fault-Low Pressure 3 Yes Hard or Soft Low Pressure Switch has tripped (<40 psi for 30 continuous sec.)
Fault-Freeze Detection FP2 4 Yes Hard or Soft Freeze protection sensor has tripped (<15 or 30 degF for 30 continuous sec.)
Fault-Freeze Detection FP1 5 Yes Hard or Soft Freeze protection sensor has tripped (<15 or 30 degF for 30 continuous sec.)
Fault-Condensate Overflow 7 Yes Hard or Soft Condensate switch has shown continuity for 30 continuous sec.
Fault-Over/Under Voltage 8 No Auto Instantaneous voltage is out of range. **Controls shut down until resolved.
Fault-FP1 & 2 Snsr Error 11 Yes Hard or Soft If FP1 or 2 Sensor Error
ABC & A
XB A
d
v
anc
ed F
aults
Fault-Compressor Monitor 10 Yes Hard or Soft Open Crkt, Run, Start or welded cont
Non-CriticAXBSnsrErr 13 No Auto Any Other Sensor Error
CriticAXBSnsrErr 14 Yes Hard or Soft Sensor Error for EEV or HW
Alert-HotWtr 15 No Auto HW over limit or logic lockout. HW pump deactivated.
Fault-VarSpdPump 16 No Auto Alert is read from PWM feedback.
Not Used 17 No Auto IZ2 Com Fault. Autoreset upon condition removal.
Non-CritComErr 18 No Auto Any non-critical com error
Fault-CritComErr 19 No Auto Any critical com error. Auto reset upon condition removal
Alarm - Low Loop Pressure 21 No Auto Loop pressure is below 3 psi for more than 3 minutes
Alarm - Home Automation 1 23 No Auto Closed contact input is present on Dig 2 input - Text is configurable
Alarm - Home Automation 2 24 No Auto Closed contact input is present on Dig 3 input - Text is configurable
NOTES:
*All codes >11 use long flash for tens digit and short flash for the ones digit. 20, 30, 40, 50 etc. are skipped!
Alert’ is a noncritical sensor or function that has failed. Normal operation of the heat pump is maintained but service is desired at some point.
Fault LED (LED1, Red)
Red Fault LED
LED Flash
Code*
Lockout
Reset/
Remove
ABC Basic F
aults
Normal - No Faults OFF –
Fault - Input 1 No Auto
Fault - High Pressure 2 Yes Hard or Soft
Fault - Low Pressure 3 Yes Hard or Soft
Fault - Freeze Detection FP2 4 Yes Hard or Soft
Fault - Freeze Detection FP1 5 Yes Hard or Soft
Fault - Condensate Overflow 7 Yes Hard or Soft
Fault - Over/Under Voltage 8 No Auto
Fault - FP1 & FP2 Sensor Error 11 Yes Hard or Soft
NOTE: All codes >11 use long flash for tens digit and short flash for the ones
digit. 20, 30, 40, 50, etc. are skipped.
Aurora Base Fault Codes (ABC Only)
Aurora Advanced Fault Codes (ABC + AXB Expansion Board)
Controls - UPC DDC Control (optional) cont.