SkyRC T6755 Charger - Manual (Page 7)

CELLS CAPACITY
BATT TYPE
Pb
Lilon
OPERATION
VOLT METER
BAL CHARGE
START SETTING PRESET
LiPo
mAh
LiPo 6S C6.0A / D2.0A P1
FAST CHG
CELLS CAPACITY
BATT TYPE
Pb
Lilon
OPERATION
VOLT METER
BAL CHARGE
START SETTING PRESET
LiPo
mAh
LiPo 6S C6.0A / D2.0A P1
FAST CHG
NiMH
NiCd
RE-PEAK
CYCLE
VOLT METER
Pb
Batt
Type Operation
Program
Description
This charging mode is for charging LiPo/LiFe/LiIon battery in normal mode.
This program is for charging or discharging lithium battery which will not be
used for long time.
The charging capacity may be a bit smaller than normal charging but the
process time will be reduced.
This mode is for balancing the voltage of lithium-polymer battery cells while
charging.
Note: We recommend charging lithium batteries with a balance wire
in the balance mode only.
The user can check lithium battery's total voltage, the highest voltage, the
lowest voltage and each cell's voltage.
The charger will charge NiMH and NiCd batteries using the charge current
set by the user.
In this program the charger detects the condition of the battery which is
connected to the output and automatically charges the battery.
Note: you should set up the upper limit of the charge current to avoid
damage by excessive feeding current. Some batteries of low
resistance and capacity can lead to higher current.
In re-peak charge mode, the charger can peak charge the battery once,
twice or three times in a row automatically. This is good for confirming the
battery is fully charged, and for checking how well the battery receives fast
charges.
1 to 5 cyclic and continuous process of charge>discharge or
discharge>charge is operable for battery refreshing and balancing to
stimulate the battery's activity.
The user can check Nickel battery's total voltage.
LiPo
Lilon
LiFe
CHARGE
DISCHARGE
STORAGE
FAST CHG
BAL CHARGE
VOLT METER
CHARGE
AUTO CHG
DISCHARGE
CHARGE
DISCHARGE
3. Charging Program
Depends on different battery type, the operation programs are different.
4. Program Start
Touch start button or touch and hold
the program.
And the charger will detects battery cells automatically. If the detecting result and your
setting are identical, the charger will start working automatically. the framed operation program for 3 seconds to start
This mode is for discharging LiPo/LiFe/LiIon battery.
This mode is for discharging NiMH/NiCd battery.
This mode is for charging Pb battery.
This mode is for discharging Pb battery.
BAL CHARGE
CHECK BATTERY… OK
BAL CHARGE
CAPACITY: 40mAh
TIME 00 02 00 : : :
CURRENT 2 0A : .
VOL 16.7V :
E.TEMP 0 C :
I. TEMP 36 C :
BALANCE
STATUS
GRAPH STOP
Please touch the arrow ▲and ▼ to find the desired operation program and the selected
one will be framed.
If the setting is wrong, it will shows the error message which is not matching your battery
parameter and you have to touch HOME to back to homepage to re-set the parameter
before going ahead.
OPERATION PROGRAM OPERATION PROGRAM
T6755 T6755 11 10
VOLT METER The user can check Pb battery's total voltage.
E.TEMP=External Temperature
(Battery Temperature)
Temperature probe must be
attached to the charger
I.TEMP=Charger’s Internal Temperature
LiPo 6S C6.0A / D2.0A P1
LiPo 6S C6.0A / D2.0A P1
BAL CHARGE
CHECK BATTERY ... ERROR
CELL NUMBER ERROR
HOME
LiPo 6S C6.0A / D2.0A P1
allowed Max Rate is adjustable independently, so the Battery Capacity setting mainly
provides additional safety monitoring.
Touch the arrow and to select the charge/discharging current if you want to modify.
CAUTION! BE SURE you know what Charge/Discharge Current setting to use for your
battery.
▲ ▲