Simaudio 700i Integrated Amplifier - Manual (Page 11)

700i Reference Dual-Mono Integrated Amplifier
____________________________________________________________________________________
11
14. The factory default of “BYPASS N” will appear in
the display. Use the volume control to alternate
between “BYPASS N” and “BYPASS Y” and then
press “OK”. Next you will be asked to confirm
your selection as “SURE ? N” will appear in the
display. Rotate the volume control until “SURE ?
Y” appears in the display. Press “OK” and
“SAVED” will briefly appear in the display
followed by “BYPASS”. When you set the
volume bypass to “Y”, the volume setting you
saved for the input with “OFFSET” will be
maintained.
15. The fifth and final configurable option for the B1
input is to disable it when it won’t be used.
Slowly rotate the volume control clockwise and
“ENABLE” will appear in the display. Press “OK”.
16. The factory default is “ENABLE Y” which will
appear in the display. Use the volume control to
alternate between “ENABLE N” and “ENABLE Y”.
Press “OK” and “SAVED” will briefly appear in
the display followed by “ENABLE”. When an
input has been disabled it will appear only in the
Setup menu as “B1 N/A”.
17. You have now passed through all five
configuration options for the B1 input. At this
point, you can (i) repeat the above process for
the another input by pressing the “Setup” button
and then use the volume control to select the
next input to configure, (ii) exit from the Setup
procedure by pressing the “Setup” button three
times or (iii) continue with the Setup procedure
by assigning the 12 Volt trigger outputs,
disabling the infrared remote sensor, changing
the IR codes, or resetting the 700i back to
factory default status (see the following
examples).
The MOON 700i is equipped with software that
allows the MiND app to control various features of
this preamplifier. With the MiND app you will be able
to adjust the volume level, mute the output, place
the preamplifier into ‘Standby’ mode and then place
it back into operational mode. As well, when you
begin playing a music track from the MiND app, the
700i will automatically switch to the input
configured for the MiND. With the MiND app, you
are essentially controlling your entire MOON system
using a hand-held Apple (iPad, iPhone, iPod Touch,)
or Android device.
You don’t need to LABEL an input with “MiND” to
achieve these aforementioned functions, but you
must configure one input for MiND functionality. An
example for this scenario would be the 180 MiND
streaming device feeding a digital signal to a MOON
750D DAC /Transport , which then outputs its
analog signal to the MOON 700i. Only one of the
five inputs may be configured for the MiND. “B1” is
the default input. If, in the previous section, you
already assigned the “MiND” label to one of this
preamplifier’s inputs, then there’s nothing required
to do here – The corresponding input has been
automatically configured for MiND and cannot be
changed until you change the input ‘LABEL”
assigments. However, if you haven’t assigned the
“MiND” label to one of the 700i’s inputs, the
following example shows how to configure an input
for MiND functionality:
1. You may either continue where we left off in the
previous example by pressing “Setup” twice to
return to the main menu and the turn the
volume control until “MiND” appears in the
display OR enter into the “Setup” mode from the
beginning by pressing the “Setup” button and
rotating the volume control until “MiND” appears
in the display.
2. Press “OK” and “MiND:B1” will appear in the
display.
3. Rotate the volume control clockwise until the
input you want to configure appears in the
display.
4. Press “OK” and “SAVED” will appear brielfy in
the display followed by “MiND”.
5. Press the “Setup” button and “EXITING” will
appear in the display.