Desa CGEFP33NRB - Manual (Page 23)

111245-01A
For more information, visit www.desatech.com For more information, visit www.desatech.com
23
23
OPERATING FIREPLACE
For Your Safety Read Before Lighting
Normal Lighting Instructions
OPERATING FIREPLACE
FOR YOUR SAFETY
READ BEFORE LIGHTING
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing prop-
erty damage, personal injury or loss of life.
A. This appliance has a pilot which lights automatically when
using the supplied wall switch or remote control. If you
have a power outage, the pilot may be lighted by hand with
push-button piezo ignitor. When lighting the pilot, the fol-
lowing warnings must be followed.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in
your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire de-
partment.
C. Electric Power Outage Only: Use only your hand to turn
the manual override handle on the gas control knob. Never
use tools. If the knob will not turn by hand, don’t try to
repair it, call a qualified service technician or gas supplier.
Force or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
NORMAL LIGHTING
INSTRUCTIONS
WARNING: You must operate this heater with the
fireplace screen in place. Make sure fireplace screen is
in place before running heater.
NOTICE: During initial operation of new heater, burning
logs will give off a paper-burning smell. Open damper or
window to vent smell. This will only last a few hours.
1. STOP! Read the safety information above.
2. Make sure equipment shutoff valve is fully open.
3. Wait five (5) minutes to clear out any gas. Smell for gas
around heater and near floor. If you smell gas, STOP! Fol-
low “B” in the safety information on warnings plate. If you
don’t smell gas, go to the next step.
ON OFF HI LO
MANUAL
IGNITION
Figure 47 - Control Locations
Manual Ignition Bypass
Switch (Up is for
Remote Control)
ON/OFF Button
HI/LO
Button
Wall
Switch
Assembly
LED
CAUTION: Do not try to adjust heating levels by
using the equipment shutoff valve.
Automatic
Ignitor
Electrode
Figure 48 - Pilot (Natural Gas)
Manual Ignitor
Electrode
Figure 49 - Pilot (Propane/LP Gas)
Automatic
Ignitor
Electrode Pilot
Burner
Manual
Ignitor
Electrode
Pilot
Burner
A. Using Supplied Wall Switch Assembly
1. Set manual ignition bypass switch on the control panel to
the OFF position (automatic ignition position).
2. Press ON/OFF button. Hold for 6 seconds. Gas valve will
open and electronic ignition will begin sparking to light
pilot. LED will light.
Note: You may be running this heater
for the first time after connecting to gas supply or at the
start of your heating season. If so, the ON/OFF button may
need to be pressed again. This will allow air to bleed from
gas system. If several attempts to light pilot fail, contact a
qualified service person or gas supplier for repairs. Until
repairs are made, light and operate manually (see Manual
Lighting Instructions for Electric Power Outage, page 24).
3. When pilot flame is lit, the thermocouple is heated by the
flame. When thermocouple becomes hot (5 to 15 seconds),
main burner will automatically light on high flame.
4. To lower flame, push HI/LO button on wall switch once.
Note: This fireplace does not have a pilot-only mode.