Dynavector DV 10X5 cartridge - Manual

Description
The Dynavector 10X series High Output Moving
Coil cartridge debuted in 1978 winning the
prestigious Design and Engineering Award at the
Chicago CES in both 1978 and 1981. The 10X
series cartridges are also widely accepted as the
benchmark in High Output moving coil cartridges at
this price point and beyond.
With the introduction of the new 10X5 High
Output moving coil there is no doubt Dynavector will
retain this enviable position and again set the
standard for high output moving coil cartridges.
Improvements
The 10X5 now features Dynavector's unique flux
damping and softened magnetism (patent) along with
powerful neodymium magnet that combine to
eliminate any hardness or irritating edginess that
commonly occurs in many moving coil cartridges.
Dynavector are also renowned for the capability
of winding the finenest coil assemblies. This has
enabled them to minutely increase the coil wire
diameter 10X5 to achieve a reduction of impedance
to 150 ohms whilist retaining a healthy 2.8mV
output. This also ensures both a rugged and
reliable circuitry.
The 10X5 also features a newly designed
Aluminium head block to provide a rigid platform for
the cartridge motor and secure fxing to the tonearm.
Stylus Replacement and Warranty
In the case of a worn stylus Dynavector
undertake to provide a replacement at a special
discount rate. This same special discount applies to
all non warranty claims please consult your retailer
for details.
The cartridge is guaranteed for a period of one
year from date of purchase against electrical and
mechanical defects provided the instructions have
been adhered to and the form overleaf has been
completed.
The guarantee does not cover stylus wear nor
cover damage to the stylus assembly arising from
mishandling or abuse. Should a defect occur the
cartridge and its casing together with the guarantee
card should be carefully packed and returned to the
retailer.
Dynavector MC Cartridge 10X5
Stylus Cleaning
Keep your records clean. Dust causes record
wear and sonic distortion. When cleaning the stylus,
use the soft brush suppled with the cartidge. Brush
only from back to front to avoid damage to the
stylus assembly. If a dark deposit like tan should
appear on the stylus tip, always use the soft brush
with a minium amount of the high quality stylus
cleaning fluid. No-alcohol stylus cleaning fluid is
recommended in a routine maintenance. We do
n o t r e c o m m e n d t o u s e c o m m e r c i a l c l e a n i n g
vibrators.
16-15 Iwamoto-cho 2-chome Chiyoda-ku
Tokyo 101-0032 Japan
Phone +81-(0)3-3861-4341 FAX +81-(0)3-3862-1650
http://www.dynavector.com/
Dynavector Systems, Ltd.
This product can be recycled. Products bearing this
symbol must NOT be thrown away with normal household
waste. At the end of the product's life, take it to a collection
point designated for recycling of electrical and electronic
devices. Find out more about return and collection points
through your local authority.
The European Waste Electrical and Electronic Equipment
(WEEE) Directive was implemented to dramatically reduce
the amount of waste going to landfills, there by reducing
the environmental impact on the planet and on human
health. Please act responsibly by recycling used products.
If this product is still useable, consider giving it away or
selling it.
: High output MC cartridge with Flux
damper and Softened magnetism
: 2.5 mV (at 1KHz, 5cm/sec.)
: 20 - 20,000Hz ( 2dB)
: 25 dB (at 1KHz)
: 1.0 dB (at 1KHz)
: 12 x 10-6 cm/dyne
: R=150 ohms
: Elliptical Nude diamond
: 6mm length aluminium pipe
: 1.8 - 2.2 grams
: >1000 ohms
Type
Output voltage
Frequency response
Channel Separation
Channel balance
Compliance
Impedance
Stylus
Cantilever
Tracking force
Recommended load
impedance
Weight
Specifications
: 7.3g
Mounting to the Headshell
Please use the M2.5 enclosed screws to mount the
cartridge. The overhang should be aligned according
to the instruction manual for the tonearm.
Connection
Connect the lead wires from the headshell to
each pin shown below.
EM1107111000S