Dynavector DV XX2MKII cartridge - Manual

This product can be recycled. Products bearing this symbol must NOT
be thrown away with normal household waste. At the end of the product's
life, take it to a collection point designated for recycling of electrical and
electronic devices. Find out more about return and collection points through
your local authority.
The European Waste Electrical and Electronic Equipment (WEEE)
Directive was implemented to dramatically reduce the amount of waste
going to landfills, there by reducing the environmental impact on the planet
and on human health. Please act responsibly by recycling used products. If
this product is still useable, consider giving it away or selling it.
n
Connection
Connect the lead wires from the headshell to each pin
shown below.
Dynavector Moving Coil Cartridge DV XX-2 MKII
16-15 Iwamoto-cho 2-chome
Chiyoda-ku Tokyo 101-0032 Japan
Phone +81(0)3-3861-4341 Fax +81(0)3-3862-1650
n
Description
Dynavector have remained the worlds leading moving
coil manufacturer since 1987. The DV XX-2 MKII is the
outstanding result of Dynavectors' continuing research
and advanced technology. Although the construction of
the XX-2 MKII is both sturdy and rigid it is never the less
a precision instrument. Due care and attention during
installation and handling will ensure optimum performance
and years of listening pleasure.
The DV XX-1 was the first cartridge to feature a
"magnetic flux damper" (patent) and softened magnetism"
(patent) processes that reject the magnetic fluctuation that
is detrimental to a moving coil cartridges performance.
n
Improvents
The DV XX-2 MKII retains the benefit of the flux damper
but features the Alinco-5 magnet and the similar rigid
construction to the Te Kaitora Rua. Alnico magnets
exhibit high magnetic flux density combining with a low
coercive therefore magnetic resistance is lower than other
magnetic types such as rare earth and ferrite, providing
the exceptional stability of the XX-2 MKII output voltage.
There is also the additional advantage of low magnetic
and electrical resistance contributing to a discernable
improvement in sound quality.
n
Stylus Replacement and Warranty
Dynavector operate an exchange scheme for the XX-2
MKII which entails rebuilding the cartridge. The rebuild
includes replacing all moving parts, ie the cantilever and
stylus assembly as well as the coils and suspension. This
allows replacement stylus cost to be minimised.
To qualify for an exchange please return the cartridge to
your dealer or national distributor.
The cartridge is guaranteed for a period of one year from
date of purchase against electrical and mechanical defects
excluding user's mishandling or abuse.
If there is any problem please consult your authorised
dealer first for service. Should it prove necessary to return
the cartridge to the factory, you should return the defective
cartridge to your dealer or national distributor, together
with the warranty card. Please keep your original packing
for safe shipping.
n
Stylus Cleaning
Keep your records clean. Dust causes record wear and
sonic distortion. When cleaning the stylus use the soft
brush supplied with the cartridge. Brush only from back
to front to avoid damage to the stylus assembly. If a dark
deposit like tan should appear on the stylus tip, always
use the soft brush with a minium amount of of high quality
stylus cleaning fluid. No-alcohol stylus cleaning fluid is
recommended in a routine maintenance.
We do not recommend to use commercial cleaning
vibrators.
n
Mounting to the Headshell
Please use M2.5mm enclosed screws to mount the
cartridge. The overhang should be aligned according to
the instruction manual for the tonarm.
n
Specifications
Type : : Low output moving coil
cartridge with flux damper
Output voltage : 0.28mV (at 1KHz, 5cm/sec.)
Frequency response: : 20 - 20,000Hz ( 1dB)
Channel separation : 30 dB (at 1KHz)
Channel balance : 1.0 dB (at 1KHz)
Compliance : 10 x 10-6 cm/dyne
Impedance : R= 6 ohms
Stylus tip : PF Line contact shape
stylus radius 7 x 30 micron
Cantilever : 6mm length solid boron
Tracking force : 1.8 - 2.2 grams
Recommended load : 30 ohms
impedance
Weight : 8.9 grams
1107120001V2
The XX-2 MKII also exhibits deep powerful bass, treble
is both clear and lively possessing none of the hardness
found in many moving coil designs. This can be accredited
to not only Dynavector's skilled assembly techniques
but also a meticulous attention to design, materials, and
engineering expertise.