beautypg.com

Venting installation, Continued, High altitude installation – Desa CSDPBN User Manual

Page 19: Parts lists for venting kits and components

background image

111739-01A

For more information, visit www.desatech.com

For more information, visit www.desatech.com

19

19

VENTING INSTALLATION

Continued

HIGH ALTITUDE INSTALLATION

Your cast iron stove and direct-vent burner system has been CSA
tested and approved for operation at altitudes in the USA from 0-
2000 ft. (0-609 m) and in Canada from 0-4500 ft. (0-1.37 km)

When installing this stove at an elevation above 2000 feet (in the
USA), you may need to decrease the input rating by changing the
existing burner orifice to a smaller size. Reduce input 4% for each
1000 feet (304.8 m) above sea level. Check with your local gas
company for proper orifice size identification and proper orifice for
your location..

When installing this stove at an elevation above 4500 feet (1.37 km)
(in Canada), check with local authorities.

For assistance with any high altitude installation contact DESA's
Technical Service Department at 1-866-672-6040.

Figure 41 - Vertical Venting Configuration With No
Horizontal Run

Vertical Venting

V = 40' (12.19 m) max.

Note: Install restrictor
into 4" (10.16 cm) collar
of burner system as
shown.

PARTS LISTS FOR VENTING KITS AND
COMPONENTS

Number

Description

VKG-47-K

Ground Floor Vent Kit, Black

Includes: Horizontal Square Termination, 90° Elbow,
7"-12" (17.78 cm - 0.3 m) Adjustable Coaxial Pipe, 6"
(15.24 cm) Pipe Adaptor, 12" (0.3 m) Coaxial Pipe,
Wall Firestop, Decorative Trim Plate and 18 Screws

VKB-47-K

Basement Vent Kit

Includes: Horizontal Square Termination, 90° Elbow,
7"-12" (17.78 cm - 0.3 m) Adjustable Coaxial Pipe, 6"
(15.24 cm) Pipe Adaptor, 4' (1.22 m) Coaxial Pipe,
Wall Firestop, Decorative Trim Plate and 18 Screws

VKS-47-K

Snorkel Vent Kit

Includes: 36" (0.91 m) Snorkel Termination, 90° Elbow,
7"-12" (17.78 cm - 0.3 m) Adjustable Coaxial Pipe, 6"
(15.24 cm) Pipe Adaptor, 4' (1.22 m) Coaxial Pipe, Wall
Firestop, Decorative Trim Plate and 18 Screws

VKR-47-K

Roof Vent Kit

Includes: Vertical High Wind Termination, Flue Re-
strictor, 7"-12" (17.78 cm - 0.3 m) Adjustable Coaxial
Pipe, 6" (15.24 cm) Pipe Adaptor, 12" (0.3 m) Coaxial
Pipe, 4' (1.22 m) Coaxial Pipe, Firestop Decorative
Trim Plate, Roof Flashing, Storm Collar and 18 Screws

P-47-12-K

12" (0.3 m) Black Coaxial Pipe (1 pk)

P-47-24-K

24" (0.61 m) Black Coaxial Pipe (1 pk)

P-47-48-K

48" (1.22 m) Black Coaxial Pipe (1 pk)

PA47-712-K 7"-12" (17.78 cm - 0.3 m) Black Coaxial Pipe (1 pk)

P-47-6-K

6" (15.24 cm) Black Coaxial Pipe (1 pk)

E47-90-K

90° Elbow (1 pk)

E47-45-K

45° Elbow (1 pk)

PA-47-6-K

6" (15.24 cm) Adaptor Collar, Black (1 pk)

WS-47

Wall Strap (1 pk)

SC-47

Storm Collar (1 pk)

VT-47

Vertical Round Termination (1 pk)

WF-47

Wall Firestop (1 pk)

VR-47

Vertical Restrictor (1 pk)

FP-47

Firestop Plate (1 pk)

HTS-47

Horizontal Square Termination (1 pk)

CS-47

Cathedral Ceiling Support Box (1 pk)

RF-47-6

Roof Flashing 0 to 6/12 Pitch (1 pk)

RF-47-12

Roof Flashing 6/12 to 12/12 Pitch (1 pk)

S-47

Vinyl Siding Standoff (1 pk)

TP-47

Trim Plate, Black (1 pk)

HT-47

Horizontal Round Termination (1 pk)

ST-47-14

14" (0.36 m) Snorkel Termination (1 pk)

ST-47-36

36" (0.91 m) Snorkel Termination (1 pk)

VENTING INSTALLATION

Installation for Vertical Termination (Cont.)

High Altitude Installation

Parts List for Venting Kits and Components

This manual is related to the following products: