Autostart AS-6265iSH - Manual (Page 6)

To take the system out of Valet Mode:
1. Hold down the unlock and start buttons simultaneously for 3 seconds.
2. The Parking Lights will flash 2 times.
The siren will chirp twice, then pause, then chirp twice again, and the LED will go out .
"Home Valet" Mode
This safety feature will remotely place the vehicle into a no-remote-start mode: if the
vehicle is parked indoors there is no danger of the vehicle starting by accident with the
remote control.
Note: Once the Home Valet Mode is activated, the vehicle will not start by remote.
To activate the Home Valet Mode:
Press the lock or unlock button.
Within 3 seconds, press the stop button until the parking lights go out.
To disable the Home Valet Mode:
Turn the ignition key to the ignition on ( run ) position.
The system will warn you if someone attempts to start your vehicle while it stands in
Home Valet Mode. The parking lights will:
Go on then off ; then
Flash twice, pause; then
Flash twice again.
Panic Mode
Safety feature: Activate Panic Mode in an emergency situation.
In an emergency situation, you can activate Panic Mode using the lock or unlock button.
This will:
Shut down the engine, Disarm the Starter Kill and
Unlock the doors (if unlock is Activate the siren for 1 minute.
pressed) (See below for a description of the Starter
Or lock the door (if lock is pressed), Kill.)
To activate Panic Mode
Press and hold the unlock button for approximately 3 seconds until the siren starts to
sound and the parking lights flash: this will unlock the doors before the siren sounds.
Or press and hold the lock button for approximately 3 seconds until the siren starts to
sound and the parking lights flash: this will lock the doors before the siren sounds.
Panic Mode will automatically shut down after 1 minute.
Note: To stop Panic Mode before the 1-minute delay, press the lock or unlock button until
the siren stops.
Quick Lockout^ M
(Also called Secure Panic.) For fast protection, the system will lock all doors when you
press the brake pedal while the siren is sounding. (Quick Lockout is only available
when Panic has been activated.)
User Guide P. 6
Cold Weather Mode
Ready mode should be set before entering Cold Weather. When the Cold Weather
Mode is active, the engine starts every 2 hours and runs for 3 minutes (or for 8 or 20
minutes with Diesel engines); the routine will go on for a period of 24 hours.
To enter Cold Weather Mode:
Press and hold the stop button for 3 seconds until the parking lights flash 3 times.
(If Safe Start is enabled, the start button must be pressed beforehand - see below.)
To enter Cold Weather Mode if Safe Start has been activated:
Press and hold the stop button for 3 seconds until the parking lights flash 3 times.
To exit Cold Weather Mode, do any one of the following:
Open the hood.
Start the engine using the remote control.
Turn the ignition key to the ignition on ( run ) position.
Press and hold the stop button for 3 seconds. (The parking lights will flash once.)
To check whether Cold Weather Mode is active, press and release the brake pedal: the
parking lights should stay on while your foot is on the brake pedal.
Priority Door Access
This safety feature lets you unlock only the driver’s door when you press the unlock
button on the transmitter, and then unlock the rest of the vehicle doors if the unlock
button is pressed for a second time within 3 seconds.
Chirp Delete
To temporarily disable the siren’s chirp confirmations upon arming and disarming (e.g. in
a quiet neighbourhood):
1. Press the trunk button, the Parking Light will flash once
2. Within 3 seconds, press the lock or unlock button to arm or disarm without any
chirps.
Note: Your installer can program the Chirps Disabled feature if you want the chirps to be
permanently disabled.
Shock Delete
The shock sensor can be temporarily disabled. To temporarily disable shock and warn-
away sense:
Press the trunk button and, within 3 seconds,
Press the stop button.
Shock senses will now be ignored until the next disarming of the system.
User-selectable Options
The system was designed with flexibility and OEM integration in mind. With its
programmable options, this unit can single-handedly control nearly any electrical system
in your vehicle.
Note: The programming of your system should be left to a professional. Changing any one
of the settings may affect the operation of your system.
P. 7 User Guide