Autostart AS-6265iSH - Manual (Page 3)

In passive Mode, the Starter Kill can be set to arm automatically in 30 seconds either
with or without Siren chirps.
To disarm the Starter Kill, press and hold the unlock button on the transmitter. The
parking lights will flash twice. (If door locks were installed, this will also unlock the doors.)
In passive Mode, the system will automatically re-arm itself 30 seconds after unlocking
the doors if the key has not been inserted in the ignition by then.
To arm the Starter Kill, press and hold the lock button on the transmitter. The parking
lights will flash once. (If the door locks were installed, this will also lock the doors.)
Turbo Mode
If Turbo Mode is configured at installation, it will allow a turbocharger to idle down after
the user leaves the vehicle: the unit will take over the vehicle and keep it running for 60
seconds (or until it is shut down by remote control), then shut down the engine and set
the Remote Car Starter to Ready Mode.
Follow all steps of the Ready Mode routine, to activate Turbo Mode:
1. Ensure that all the doors are closed and that the shifter is in the neutral position.
2. With the engine already running, apply the parking brake and release the brake
Pedal.
Make sure to release the brake pedal.
3. Within 20 sec. Press lock , unlock or start on the transmitter.
The parking lights will flash 3 times quickly and remain lit.
4. Remove the key: the engine will go on running.
5. Exit the vehicle and close the door.
6. Press and hold either:
a. lock to lock the doors and shut down the engine after 60 sec.;
b. unlock to unlock the doors and shut down the engine after 60 sec.;
c. stop to shut down the engine immediately, without affecting the doors
(this will by-pass Turbo Mode).
d. trunk to set the vehicle into idle mode
Engine Run Time
If you have a gas engine, your system can be programmed to run the engine for 3, 15, or
25 minutes (15 min default). If you have a diesel engine, it can be programmed to run the
engine for 8, 20, or 30 minutes (20 min default).
Extended Run Time
With the vehicle running under a remote start, bressinfl and holding the start button foil
more than 1 second^ will reset the run time counter to zero and restart the run time cycle
from the beginning.
To stop the vehicle, at any moment, simply press the stop button. This procedure can
only be carried out once per remote start.
Example: if your Module is programmed for a run time of 3 minutes and your vehicle has
been running for 2 minutes already, pressing the start button will reset the counter to
zero and the Engine will run for another cycle (in this case, 3 minutes).
User Guide P. 10
The functions of the transmitter are as follows:
e
LOCK: LùC\i\. LhÉ ÌXtùtì and ar№
ThP STARTER Klli.
UNLOCK^ Untodis.W hxn jnO
Uunm me ST
a KTEK KILL.
AjCLhuiles [he AUX 2 auCjxii IF
D i » r ' L
s
ItUhK: me miNK «
■utivjtn die AJX J oulptft.
RiHvi«« uiru ihe EiyJrie
o
iTO^l
5[0[K [hi enelne Of Ì4Q dii k\o>
Cc4d 'WtailM' MiHJif IT prfadiiJ fpr
3
Note: Pressing the lock and unlock buttons at the same time will activate the aux 2 output.
Remote-starting Your Vehicle
Setting Your Vehicle Into Ready Mode
In order to start the vehicle by remote, the unit must first be set to Ready Mode. If the
unit is not set to Ready Mode, it cannot remote-start the vehicle.
Once the system is set to Ready Mode, the vehicle can be remote-started and stopped at
wish.
To set the system to Ready Mode:
1. Ensure that all the doors are closed and that the shifter is in the neutral
position.
2. With the engine already running, apply the parking brake and release the brake
pedal.
Make sure to release the brake pedal.
3.
Within 20 sec. press lock , unlock or start on the transmitter.
The parking lights will flash 3 times quickly and remain lit.
4.
Remove the key: the engine will go on running.
5. Exit the vehicle and close the door.
6. Press and hold either:
a. lock to lock the doors and shut down the engine;
b. unlock to unlock the doors and shut down the engine;
c. stop to shut down the engine without affecting the doors.
Remaining In Ready Mode
Once the vehicle is in Ready Mode you can start and stop the vehicle at wish. However,
should any of the following occur, the vehicle will exit Ready Mode - thus eliminating the
remote start option until Ready Mode is restored:
1. Door opened;
2. Hood opened;
3. Brake pedal pressed;
4. Parking brake disengaged;
5. Ignition key turned to the
ignition on ( run ) position.
Note: The unit will notify the user that it has exited Ready Mode by giving 3 slow flashes
(parking lights).
P. 3 User Guide