Autostart AS-6265iSH - Manual (Page 5)

The user-selectable options are as follows:
Safe Start Ignition Re-Lock
Remote Door Locks Secure Lock
Passive or Active Arming Remote Trunk Release
Disarm Notification Starter Kill
Shock Sense and Warn-Away Sense Engine Run Time
Siren Chirps
Ignition-Controlled Door Locks
Multi-Car Operation
Safe Start
Safety feature: Safe Start features will prevent accidental remote starts.
If this feature Is enabled, the user must press the start button 2 times within 3 seconds
to remote-start the vehicle.
If Swap Start Mode has been configured by your Installer, to remote-start your vehicle
press LOCK and unlock simultaneously. (Press start to trigger the aux 2 output.)
Safe Start features will eliminate accidental remote starts, e.g. when there are children
playing with the transmitter.
Remote Door Locks
If your system was Installed with the Remote Door Locks option, you will have the
convenience of remote keyless entry.
To unlock your doors and disarm the system:
1. Press and hold the unlock button for approx. 1 sec.
2. The parking lights will flash twice and the LED will go out to confirm that the doors
have been unlocked, that the Starter Kill feature Is disarmed (If It was Installed) and
that the Alarm Is disabled.
To LOCK your doors and arm the system:
1. Press and hold the lock button for approx. 1 sec.
2. The parking lights will flash once and the LED will flash slowly to confirm that the
doors have been locked, that the Starter Kill feature Is enabled (If It was Installed)
and that the Alarm Is armed.
Passive or Active Arming
By default, the system is configured to Passive Arming Mode. In Passive Arming Mode,
the Starter Kill and the Alarm will automatically arm 30 seconds after the last door is
closed. The system will not arm itself if a door is left open.
Important note: When the system re-arms automatically or if there is an Alarm condition, you
can disarm the system by simply pressing the unlock button.
Disarmed Notification
( off by default.) This feature will notify the user when the vehicle was left disarmed: after
the Engine has been shut down and all doors have been closed, after 10 seconds the
horn will honk once if the doors have been left unlocked.
Shock Sense And Warn-Away Sense
(Both enabled by default.) This system can react to a full shock by triggering the Alarm; it
can also respond to a lighter shock (30 % of the strength of a full shock) by giving a
warn-away (without triggering an Alarm condition). When the Engine is running after a
remote start, however, the system will prevent any Alarm condition to be triggered ;
it will still give a warning sound if warn-away is enabled._____________________________
User Guide P. 8
6. Press the trunk button until the system is armed (the doors will be locked if
remote door lock is installed).
If the pre-programmed run-time expires or if the user shuts down the engine by remote
control, the vehicle will get in Ready Mode.
Caution: Do not leave children or pets unattended in a car running in Idle Mode.
Valet Mode
The system can be placed in Valet Mode to disable the remote starting capabilities. If the
vehicle needs to be serviced, or if you park it indoors, the Valet Mode will prevent the
engine from being remote-started accidentally.
To put the system into Valet Mode:
1. Turn the key to the ignition on ( run ) position.
2. Within 3 sec. press the Valet button and release it, the Parking lights will flash 3
times. Turn the ignition off , the LED will come on . (The system is in Valet Mode.)
To take the system out of Valet Mode:
1. Turn the key to the ignition on ( run ) position.
2. Within 3 sec. press and release the Valet button, the Parking Lights will flash tiwce.
The LED will go out . (The system is out of Valet Mode.)
The Valet button can only be used if the ignition key is in the ignition on ( run ) position.
Ignition Valet
The system can be placed in Valet Mode to disable the remote starting capabilities. If the
vehicle needs to be serviced, or if you park it indoors, Valet Mode will prevent the engine
from being accidentally started by remote control.
To enter Valet Mode
1. With the key in the Ignition switch, turn the key to the on ( run / ignition ) and then off
positions 5 times within 10 seconds.
2. The Parking Light will flash 3 times indicating the Module is now in Valet Mode. The
LED will turn
on solid.
To exit Valet Mode
1. With the key in the Ignition switch, turn the key to the on ( run / ignition ) and then off
positions 5 times within 10 seconds.
2. The Parking Light will flash twice indicating the Module is now out of Valet Mode.
The LED will turn
off .
Remote Valet
This feature will put your vehicle into Valet Mode using the remote transmitter instead of
the Valet button as above.
Note: Once the Electronic Valet is activated, the remote starter and Alarm features are
disabled.
To put the system into Valet Mode:
1. Hold down the unlock and start buttons simultaneously for 3 seconds.
2. The Parking Lights will flash 3 times.
The siren will chirp twice and the LED will come on .
P. 5 User Guide